Wraps by car

Bitter Type 3 wrap

The Bitter Type 3 wrap is a precise job for a rare 1987–1992 sports car. This page covers the single generation of the Type 3 and the vinyl wrap it needs. A full wrap of the convertible body takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds roughly 4 ft (1.5 m) to that estimate.

1generations14.5 mof film for a full wrap

Bitter Type 3, first generation, factory photo
Bitter Type 3, first generation. Factory color shown.

Bitter Type 3 wrap colors and ideas

  • Type 3 black wrap
  • Type 3 white wrap
  • Type 3 gray wrap
  • Type 3 silver wrap
  • Type 3 red wrap
  • Type 3 blue wrap
  • Type 3 green wrap
  • Type 3 yellow wrap
  • Type 3 orange wrap
  • Type 3 purple wrap
  • Type 3 pink wrap
  • Type 3 teal wrap
  • Type 3 brown wrap
  • Type 3 gold wrap
  • Type 3 chrome wrap
  • Type 3 color shift wrap
  • Type 3 carbon fiber wrap
  • Type 3 camo and patterned wrap

How much vinyl to wrap a Bitter Type 3

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1987–1992convertible (2 doors)175.2 in (4,450 mm)about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m)

Type 3 wrap cost factors

Type 3 wrap cost is driven by the small production numbers and the age of a 1987–1992 Bitter Type 3. The 175.2 in (4,450 mm) convertible body needs about 48 ft (14.5 m) of film, and installation time rises with the many curved edges. Paint condition and any repairs before wrapping change the price more than the film choice. Custom chrome or patterned vinyl adds to the labor and material because it uses about 52 ft (16 m).

  • Film for a full wrap: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Type 3 wraps by generation

Swipe sideways. Tap a card for the full description.

Bitter Type 3, first generation, factory photo
Factory color shown

1987–1992 Type 3 convertible (first generation)

1987–1992convertible (2 doors)175.2 in (4,450 mm)

The open top of the first generation Type 3 means the fabric roof is not wrapped and the film ends where it begins. On a fabric top, the vinyl stops at the trim below the roof, so no film touches the soft material. On a folding hard top, each panel is wrapped as its own part with precise gaps. The installer must mask the roof seals to avoid adhesive or knife marks.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m).

Roof, hood, chrome delete and PPF on a Type 3

Type 3 chrome delete covers the window trim and badges in black film, which is a small job on this two-door convertible. A partial wrap of the hood, mirror caps, and rear deck uses far less film than a full wrap. Paint protection film (PPF) can be applied as clear film on the front end to guard against stone chips. These options suit owners who want to change one area without a full color change wrap.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Bitter Type 3: body, cut-outs and film

A Bitter Type 3 vinyl wrap must follow the lines of a two-door convertible that measures 175.2 in (4,450 mm) long. The compact sports car body has no fixed roof, so film stops where the fabric or folding top begins. The curved panels and short overhangs reward careful cutting and inlay work. The estimate of 48 ft (14.5 m) covers the painted areas from nose to tail.

Type 3 wrap ideas start with the convertible hood area, where the film ends cleanly below the top mechanism. For a fabric roof, the vinyl stops at the beltline and trim. For a folding hard top, each roof panel is wrapped as its own piece. Mirrors, bumpers, and door handles are removed or cut around for a neat edge.

How much vinyl to wrap a Type 3 depends on the generation, and this car has only one: the 1987–1992 convertible. There are no later body styles to compare, so the 48 ft (14.5 m) figure stays the same for every Type 3. The fabric or folding top is never wrapped, which keeps the total film use lower than a hardtop sports car of similar length.

Questions about wrapping a Bitter Type 3

How much vinyl does it take to wrap a Bitter Type 3?

A Bitter Type 3 takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film for a full wrap. Chrome or patterned film needs about 52 ft (16 m). These figures come from the 1987–1992 convertible body, which has no fixed roof to cover.

Is the top of a Type 3 wrapped?

No, the top of a Type 3 is not wrapped. The fabric roof is left uncovered and the film ends where the top begins. A folding hard top is wrapped as separate panels, but a fabric top never gets vinyl.

Can I wrap only the hood or the roof of a Type 3?

Yes, you can wrap only the hood or the roof of a Type 3. A partial wrap of the hood, mirror caps, and rear deck is a common smaller job. Paint protection film (PPF) can also be applied as clear film on the front end.

Is a Type 3 hard to wrap?

A Type 3 is not especially hard to wrap, but the convertible body adds work. The 175.2 in (4,450 mm) length is normal, yet the many curved edges and the open top mean careful cutting and masking. The film ends at the roof area, and the trim around the opening needs attention.