Wraps by car

Invicta S1 wrap

The Invicta S1 is a British sports car produced from 2004 to 2012. This page covers the vinyl wrap for the first generation, the only generation in the catalog. A full wrap of the coupe body takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film.

1generations14.5 mof film for a full wrap

Invicta S1, first generation, factory photo
Invicta S1, first generation. Factory color shown.

Invicta S1 wrap colors and ideas

  • Invicta S1 black wrap
  • Invicta S1 white wrap
  • Invicta S1 gray wrap
  • Invicta S1 silver wrap
  • Invicta S1 red wrap
  • Invicta S1 blue wrap
  • Invicta S1 green wrap
  • Invicta S1 yellow wrap
  • Invicta S1 orange wrap
  • Invicta S1 purple wrap
  • Invicta S1 pink wrap
  • Invicta S1 teal wrap
  • Invicta S1 brown wrap
  • Invicta S1 gold wrap
  • Invicta S1 chrome wrap
  • Invicta S1 color shift wrap
  • Invicta S1 carbon fiber wrap
  • Invicta S1 camo and patterned wrap

How much vinyl to wrap an Invicta S1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2004–2012coupe (2 doors)173.2 in (4,400 mm)about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m)

Invicta S1 wrap cost factors

An Invicta S1 wrap cost depends on the film type, the condition of the paint, and the shop's labor. The body is 173.2 in (4,400 mm) long, but the large doors reduce the number of panels to handle. Removing and refitting the bumpers and mirrors adds time to the job.

  • Film for a full wrap: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Invicta S1 wraps by generation

Swipe sideways. Tap a card for the full description.

Invicta S1, first generation, factory photo
Factory color shown

2004–2012 Invicta S1 coupe (first generation)

2004–2012coupe (2 doors)173.2 in (4,400 mm)

The first-generation Invicta S1 was built from 2004 to 2012. On a car of these years, panels may be original or repainted, and a test spot comes before a full wrap. A test patch shows whether the film will lift old paint when it is removed later.

Two long side doors: each door is one large piece of film.

Film: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 56 ft (17 m).

Roof, hood, chrome delete and PPF on an Invicta S1

A partial wrap on an Invicta S1 can cover the roof, hood, or mirror caps. An Invicta S1 chrome delete covers the window trim and badges with black film. Paint protection film (PPF) can be applied as clear film on the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Invicta S1: body, cut-outs and film

The Invicta S1 vinyl wrap covers a two-door coupe that is 173.2 in (4,400 mm) long. The long side doors are each fitted with one large piece of film, which keeps seams away from the middle of the panel. The smooth coupe shape has no sharp corners that would complicate the install.

For Invicta S1 wrap ideas, start with a full color change in a cast film. You can add contrast with a gloss black roof or mirror caps, leaving the rest of the body painted. The front bumper has recessed fog lamps and a deep lower intake that require careful inlays.

If you ask how much vinyl to wrap an Invicta S1, the answer is about 48 ft (14.5 m) of 60-inch (1.52 m) film for a standard color. A chrome or patterned film needs about 56 ft (17 m) because the pattern direction forces more waste. This car has one generation, so the estimate is the same for every production year.

Questions about wrapping an Invicta S1

How much vinyl does it take to wrap an Invicta S1?

It takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film to wrap an Invicta S1 in a standard color. A chrome or patterned film needs about 56 ft (17 m) because of pattern matching waste.

Can I wrap only the hood or the roof of an Invicta S1?

Yes, you can wrap only the hood or the roof of an Invicta S1. A partial wrap can also cover the mirror caps, and a chrome delete covers the window trim and badges.

Is an Invicta S1 hard to wrap?

An Invicta S1 is not hard to wrap for an installer with experience on long coupe doors. The two side doors are each one large piece of film, which takes care and a second pair of hands. The front bumper has recessed lamps and a deep intake that need inlays.

How many generations of the Invicta S1 does this page cover?

This page covers one generation of the Invicta S1. The first generation was produced from 2004 to 2012 as a two-door coupe.