Wraps by car

KTM X-Bow wrap

A KTM X-Bow wrap is a color change for one of the smallest sports cars on the road, the first generation built from 2007 to now with only a convertible body. The car measures 147.2 in (3,738 mm) long, so a vinyl wrap uses less film than most cars. The newest body takes about 36 ft (11 m) of 60-inch (1.52 m) cast film for a full color change.

1generations11 mof film for a full wrap

KTM X-Bow, first generation, factory photo
KTM X-Bow, first generation. Factory color shown.

KTM X-Bow wrap colors and ideas

  • X-Bow black wrap
  • X-Bow white wrap
  • X-Bow gray wrap
  • X-Bow silver wrap
  • X-Bow red wrap
  • X-Bow blue wrap
  • X-Bow green wrap
  • X-Bow yellow wrap
  • X-Bow orange wrap
  • X-Bow purple wrap
  • X-Bow pink wrap
  • X-Bow teal wrap
  • X-Bow brown wrap
  • X-Bow gold wrap
  • X-Bow chrome wrap
  • X-Bow color shift wrap
  • X-Bow carbon fiber wrap
  • X-Bow camo and patterned wrap

How much vinyl to wrap a KTM X-Bow

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2007–nowconvertible147.2 in (3,738 mm)about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m)

X-Bow wrap cost factors

The X-Bow wrap cost depends on the film and the labor for a car that is 147.2 in (3,738 mm) long and only a convertible, so less film is used than on a typical sedan. A chrome or patterned film needs about 46 ft (14 m), which is more than the 36 ft (11 m) of standard cast vinyl. The open top adds labor because the film must be trimmed cleanly where the fabric begins.

  • Film for a full wrap: about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).
  • Body: convertible.
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

X-Bow wraps by generation

Swipe sideways. Tap a card for the full description.

KTM X-Bow, first generation, factory photo
Factory color shown

2007–now X-Bow convertible (first generation)

2007–nowconvertible147.2 in (3,738 mm)

The open top of the first generation KTM X-Bow is not wrapped, and the vinyl film ends where the fabric begins along the windshield header and the rear deck. The film is cut and tucked at that edge so the top still closes without rubbing, and the roll bar behind the seats is wrapped as its own small panel above the body line.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).

Roof, hood, chrome delete and PPF on an X-Bow

On the KTM X-Bow you can choose a partial wrap instead of a full color change, covering only the hood, mirror caps, or rear deck. A chrome delete covers the window trim and badges with black film, and paint protection film (PPF) is a clear film applied to the front end. Each of these jobs uses less film than a full wrap and can be done on the same convertible body.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a KTM X-Bow: body, cut-outs and film

A KTM X-Bow vinyl wrap has to cover a compact convertible body that measures 147.2 in (3,738 mm) long in its only generation. The fabric top is not wrapped, so the film ends where the top begins along the windshield frame and the rear deck. The body is short from nose to tail, which keeps the number of panels small and the install simpler than on a long sedan.

X-Bow wrap ideas start with the open body, where the film must stop at the fabric top and cannot carry over the cockpit. The mirrors and the rear wing come off for a clean edge, and the badges need cut-outs around them. The front splitter and side blades are low and catch stone chips, so a shop usually wraps them as separate pieces.

How much vinyl to wrap an X-Bow depends on the film you pick, because the first generation has stayed the same width and height since 2007. A color change with 60-inch (1.52 m) cast film needs about 36 ft (11 m), but a chrome or patterned film needs about 46 ft (14 m) to match the print direction. The car is only a convertible, so the estimate from the newest body fits every year of this generation.

Questions about wrapping a KTM X-Bow

How much vinyl does it take to wrap a KTM X-Bow?

A KTM X-Bow takes about 36 ft (11 m) of 60-inch (1.52 m) cast vinyl film for a full color change wrap. If you use chrome or patterned film, the estimate rises to about 46 ft (14 m) because the pattern must be matched. The car is only a convertible, so the same figures cover every trim of the first generation from 2007 to now.

Is the top of an X-Bow wrapped?

No, the fabric top of an X-Bow is not wrapped. The film ends where the top begins along the windshield frame and the rear deck, and the top itself stays uncovered. A folding hard top would be wrapped as separate panels, but this car has only a fabric top.

Can I wrap only the hood or the roof of an X-Bow?

Yes, an X-Bow can be wrapped only on the hood or the roof panels. A partial wrap on this car also covers the mirror caps or the rear deck, and a clear paint protection film can be applied just to the front end. These smaller jobs use less vinyl than the 36 ft (11 m) needed for a full wrap.

Is an X-Bow hard to wrap?

An X-Bow is a small car to wrap, but the open convertible body adds work that a closed car does not have. The film must be trimmed where the fabric top begins, and the front splitter and side blades need extra time as separate pieces. The car is 147.2 in (3,738 mm) long, so the individual panels are short and the film goes on quickly.