Wraps by car

Pininfarina Battista wrap

The Pininfarina Battista wrap page covers the first generation of this electric sports car, produced from 2019 to now. A full vinyl wrap of the Battista takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. The car is a two-door coupe with a length of 193.4 in (4,912 mm).

1generations16.5 mof film for a full wrap

Pininfarina Battista, first generation, factory photo
Pininfarina Battista, first generation. Factory color shown.

Pininfarina Battista wrap colors and ideas

  • Battista black wrap
  • Battista white wrap
  • Battista gray wrap
  • Battista silver wrap
  • Battista red wrap
  • Battista blue wrap
  • Battista green wrap
  • Battista yellow wrap
  • Battista orange wrap
  • Battista purple wrap
  • Battista pink wrap
  • Battista teal wrap
  • Battista brown wrap
  • Battista gold wrap
  • Battista chrome wrap
  • Battista color shift wrap
  • Battista carbon fiber wrap
  • Battista camo and patterned wrap

How much vinyl to wrap a Pininfarina Battista

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2019–nowcoupe (2 doors)193.4 in (4,912 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)

Battista wrap cost factors

Battista wrap cost depends on the amount of film and the labor for the car's size. The car is 193.4 in (4,912 mm) long, and a full wrap uses about 54 ft (16.5 m) of film. A chrome or patterned film raises the amount to about 61 ft (18.5 m). The coupe body and the two long doors add to the time an installer spends on the job.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.
  • Electric car: the charge port door is wrapped as a small piece of its own.

Battista wraps by generation

Swipe sideways. Tap a card for the full description.

Pininfarina Battista, first generation, factory photo
Factory color shown

2019–now Battista coupe (first generation)

2019–nowcoupe (2 doors)193.4 in (4,912 mm)

The first generation Pininfarina Battista, built from 2019 to the present, is a two-door coupe that is 193.4 in (4,912 mm) long. Its size means a full wrap needs about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. The two long side doors are wrapped as single panels, so the car has fewer seams than a four-door. The charge port door is a separate small piece on this electric car.

Two long side doors: each door is one large piece of film.

Electric car: the charge port door is wrapped as a small piece of its own.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Battista

A Battista chrome delete covers the bright trim with black film on the window trim and badges. A partial wrap on this car can be limited to the roof, the hood, or the mirror caps. For paint protection film (PPF), a common job is a clear film on the front end to guard against stone chips. These smaller jobs use less film than a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Pininfarina Battista: body, cut-outs and film

The Pininfarina Battista vinyl wrap is shaped by the car's coupe body style and its length of 193.4 in (4,912 mm). The two long side doors are each handled as one large piece of film, which keeps the number of panels low. The low roofline and wide rear haunches require careful stretching of the film. A wrap installer will plan the layout to use the full width of the 60-inch (1.52 m) roll.

Battista wrap ideas start with the parts that need cut-outs or removal. The electric car has a charge port door, and that door is wrapped as its own small piece so it can open normally. The door handles, badges, and mirror caps are removed for a clean edge. The front and rear lights stay in place and are cut around.

How much vinyl to wrap a Battista depends on the generation, and this page covers only the first generation in production since 2019. The body size and shape have not changed in that time, so the film estimate stays the same. For a standard color change wrap, you need about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. If you choose a chrome or patterned film, the estimate rises to about 61 ft (18.5 m) because the pattern must be matched.

More Pininfarina wraps

Questions about wrapping a Pininfarina Battista

How much vinyl does it take to wrap a Pininfarina Battista?

A full wrap of a Pininfarina Battista takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. If you use a chrome or patterned film, the amount rises to about 61 ft (18.5 m). These figures are for the first generation coupe, which is the only body style in production.

Can I wrap only the hood or the roof of a Battista?

Yes, you can wrap only the hood or the roof of a Battista. The partial wrap options for this car include the roof, the hood, and the mirror caps. You can also choose a chrome delete on the window trim and badges. Those jobs use less film and take less time than a full wrap.

Is a Battista hard to wrap?

Yes, a Battista is somewhat hard to wrap because of its size and shape. The car is 193.4 in (4,912 mm) long, and the two long side doors each need one large piece of film. The charge port door on this electric car is wrapped as a separate small piece. An installer with experience on wide, low coupes will handle the job best.

How many generations of the Battista does this page cover?

This page covers one generation of the Pininfarina Battista, the first generation. It has been in production since 2019 and is the only generation in the catalog.