Wraps by car

Think City wrap

This page covers the Think City, a mini electric hatchback built from 2008 to 2012 in a single generation. A full wrap of this car uses about 41 ft (12.5 m) of 60-inch (1.52 m) cast film. The vinyl wrap process for a City focuses on its three-door hatchback body and compact dimensions.

1generations12.5 mof film for a full wrap

Think City, first generation, factory photo
Think City, first generation. Factory color shown.

Think City wrap colors and ideas

  • City black wrap
  • City white wrap
  • City gray wrap
  • City silver wrap
  • City red wrap
  • City blue wrap
  • City green wrap
  • City yellow wrap
  • City orange wrap
  • City purple wrap
  • City pink wrap
  • City teal wrap
  • City brown wrap
  • City gold wrap
  • City chrome wrap
  • City color shift wrap
  • City carbon fiber wrap
  • City camo and patterned wrap

How much vinyl to wrap a Think City

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2008–2012hatchback (3 doors)123.7 in (3,143 mm)about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

City wrap cost factors

City wrap cost depends on the number of panels, the film type, and the labor for the tailgate and charge port door. A full wrap needs about 41 ft (12.5 m) of cast film, but chrome or patterned film can increase the amount to about 51 ft (15.5 m). The car's length of 123.7 in (3,143 mm) and the two long doors also affect installation time.

  • Film for a full wrap: about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: hatchback (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.
  • Electric car: the charge port door is wrapped as a small piece of its own.

City wraps by generation

Swipe sideways. Tap a card for the full description.

Think City, first generation, factory photo
Factory color shown

2008–2012 City hatchback (first generation)

2008–2012hatchback (3 doors)123.7 in (3,143 mm)

The first-generation Think City (2008–2012) may have original or repainted panels after years of use. Before a full wrap, a test spot on the paint shows whether the film will adhere evenly. If some panels are repainted, the installer can check for peeling or weak clear coat.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Electric car: the charge port door is wrapped as a small piece of its own.

Film: about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a City

Partial wrap options for the Think City include the roof, hood, and mirror caps. For a City chrome delete, window trim and badges can be covered with black film. Paint protection film (PPF) can also be applied as clear film on the front end.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Think City: body, cut-outs and film

The Think City vinyl wrap starts with a small hatchback body that is 123.7 in (3,143 mm) long. Its three-door style means two long side doors and a tailgate, which keep the number of body panels low. The short roof and small hood use less film than a larger car.

City wrap ideas should account for the tailgate with the rear glass in it, where the film ends at the edge of the glass. Each long side door is wrapped as one large piece of film, so seams are easy to avoid. The charge port door is wrapped as a small piece of its own, allowing clean edges around the port.

To know how much vinyl to wrap a City, measure the first-generation model from 2008 to 2012. The film estimate of about 41 ft (12.5 m) assumes 60-inch (1.52 m) cast film on every body panel. If you choose chrome or patterned film, plan for about 51 ft (15.5 m).

Questions about wrapping a Think City

How much vinyl does it take to wrap a Think City?

A full wrap of a Think City takes about 41 ft (12.5 m) of 60-inch (1.52 m) cast film. The first-generation body is a compact hatchback, so it needs less film than many larger cars. If you choose chrome or patterned film, expect to use about 51 ft (15.5 m).

Can I wrap only the hood or the roof of a City?

Yes, you can wrap only the hood or the roof of a City. Partial wrap jobs on this car often include the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film, and clear paint protection film can be applied to the front end.

Is a City hard to wrap?

A City is not especially hard to wrap, but a few details add work. The tailgate has the rear glass in it, so the film must end cleanly at the edge of the glass. The two long side doors each need a single large piece of film, and the charge port door is wrapped as its own small piece.

How many generations of the City does this page cover?

This page covers one generation of the Think City, produced from 2008 to 2012. That generation is a three-door hatchback with a length of 123.7 in (3,143 mm). All wrap figures on this page refer to that body style.