Wraps by car

Vector M12 wrap

The Vector M12 wrap page covers this 1996–2000 sports car in its single generation. A full vinyl wrap of the coupe body takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film. Using chrome or patterned film adds roughly 13 ft (4 m) to the roll. The estimate is based on the car's 188.2 in (4,780 mm) overall length.

1generations14.5 mof film for a full wrap

Vector M12, first generation, factory photo
Vector M12, first generation. Factory color shown.

Vector M12 wrap colors and ideas

  • Vector M12 black wrap
  • Vector M12 white wrap
  • Vector M12 gray wrap
  • Vector M12 silver wrap
  • Vector M12 red wrap
  • Vector M12 blue wrap
  • Vector M12 green wrap
  • Vector M12 yellow wrap
  • Vector M12 orange wrap
  • Vector M12 purple wrap
  • Vector M12 pink wrap
  • Vector M12 teal wrap
  • Vector M12 brown wrap
  • Vector M12 gold wrap
  • Vector M12 chrome wrap
  • Vector M12 color shift wrap
  • Vector M12 carbon fiber wrap
  • Vector M12 camo and patterned wrap

How much vinyl to wrap a Vector M12

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1996–2000coupe (2 doors)188.2 in (4,780 mm)about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)

Vector M12 wrap cost factors

Vector M12 wrap cost depends on the film type, the amount of prep, and the condition of the 1996–2000 body. A color change wrap uses about 48 ft (14.5 m) of film, while chrome or patterned film needs about 61 ft (18.5 m). The two long side doors and the 188.2 in (4,780 mm) length add labor time. The paint condition, whether original or repainted, also changes the preparation work.

  • Film for a full wrap: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Vector M12 wraps by generation

Swipe sideways. Tap a card for the full description.

Vector M12, first generation, factory photo
Factory color shown

1996–2000 Vector M12 coupe (first generation)

1996–2000coupe (2 doors)188.2 in (4,780 mm)

The first generation Vector M12 was built from 1996 to 2000, and its paint age matters for a wrap. Panels may be original or repainted, so a test spot comes before a full wrap. On a car of these years, the installer checks every panel before stretching film. A test spot shows whether the surface will hold the adhesive correctly.

Two long side doors: each door is one large piece of film.

Film: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Vector M12

A partial wrap on a Vector M12 can cover the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end. These smaller jobs use less material than a full wrap and still change the look of the car.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Vector M12: body, cut-outs and film

A Vector M12 vinyl wrap suits the fixed-roof coupe with its two long side doors. Each door is one large piece of film, so the flat lower panels help the film lay smoothly. The 188.2 in (4,780 mm) length means the roof and rear deck use full-width material without seams. Door and quarter panels together account for most of the 48 ft (14.5 m) roll.

Vector M12 wrap ideas often start with the two doors, which are the largest single panels on the body. The doors wrap as one piece each, leaving no seam across the middle. The side mirrors, door handles, and fuel filler cap need cut-outs. The front bumper, rear bumper, and rocker panels can stay on the car during installation.

When you count how much vinyl to wrap a Vector M12, remember that this car has only one generation, produced from 1996 to 2000. There are no body style changes across those years, so the film take stays the same. The only variable is the paint underneath, which may be original or repainted. A test spot before the full wrap shows how film will stick to the surface.

Questions about wrapping a Vector M12

How much vinyl does it take to wrap a Vector M12?

It takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film to wrap a Vector M12. For chrome or patterned film, the estimate is about 61 ft (18.5 m). These figures cover the coupe body of the single generation.

Can I wrap only the hood or the roof of a Vector M12?

Yes, you can wrap only the hood or the roof of a Vector M12. Partial wraps for this car also include the mirror caps, and a chrome delete covers the window trim and badges. Paint protection film can be applied to just the front end.

Is a Vector M12 hard to wrap?

A Vector M12 is not the easiest car to wrap because of its two long side doors and 188.2 in (4,780 mm) overall length. Each door is one large piece of film, which requires careful handling. The large panels and the low sports car body add time to the installation.

How many generations of the Vector M12 does this page cover?

This page covers one generation of the Vector M12. The car was produced in a single generation from 1996 to 2000 with a coupe body style.