Wraps by car

Zenvo ST1 wrap

The Zenvo ST1 wrap page covers the 2009–2015 first generation coupe, a Danish sports car that needs about 52 ft (16 m) of 60-inch (1.52 m) cast film for a full vinyl wrap. Chrome or patterned film raises the estimate to about 59 ft (18 m). The catalog lists one generation, so the measurements stay the same for every production year.

1generations16 mof film for a full wrap

Zenvo ST1, first generation, factory photo
Zenvo ST1, first generation. Factory color shown.

Zenvo ST1 wrap colors and ideas

  • Zenvo ST1 black wrap
  • Zenvo ST1 white wrap
  • Zenvo ST1 gray wrap
  • Zenvo ST1 silver wrap
  • Zenvo ST1 red wrap
  • Zenvo ST1 blue wrap
  • Zenvo ST1 green wrap
  • Zenvo ST1 yellow wrap
  • Zenvo ST1 orange wrap
  • Zenvo ST1 purple wrap
  • Zenvo ST1 pink wrap
  • Zenvo ST1 teal wrap
  • Zenvo ST1 brown wrap
  • Zenvo ST1 gold wrap
  • Zenvo ST1 chrome wrap
  • Zenvo ST1 color shift wrap
  • Zenvo ST1 carbon fiber wrap
  • Zenvo ST1 camo and patterned wrap

How much vinyl to wrap a Zenvo ST1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2009–2015coupe (2 doors)183.7 in (4,665 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m)

Zenvo ST1 wrap cost factors

The Zenvo ST1 wrap cost depends on the size of the car, which is 183.7 in (4,665 mm) long and needs about 52 ft (16 m) of 60-inch (1.52 m) cast film for a full wrap. A color change wrap costs more than a partial wrap because it uses more film and labor. Chrome or patterned film raises the cost further, since it needs about 59 ft (18 m) of material.

  • Film for a full wrap: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Zenvo ST1 wraps by generation

Swipe sideways. Tap a card for the full description.

Zenvo ST1, first generation, factory photo
Factory color shown

2009–2015 Zenvo ST1 coupe (first generation)

2009–2015coupe (2 doors)183.7 in (4,665 mm)

The first generation Zenvo ST1 from 2009–2015 may have original or repainted panels, so a test spot on the paint comes before a full wrap. Older paint can be more fragile when film is removed later, and a test spot shows whether the surface is stable. A repainted panel may need extra prep so the film sticks evenly.

Two long side doors: each door is one large piece of film.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m).

Roof, hood, chrome delete and PPF on a Zenvo ST1

A partial wrap on a Zenvo ST1 covers the roof, hood, or mirror caps for a smaller job than a full color change. A chrome delete replaces window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Zenvo ST1: body, cut-outs and film

A Zenvo ST1 vinyl wrap covers a two-door coupe body that is 183.7 in (4,665 mm) long, with two long side doors that each take one large piece of film. The simple body style means fewer seams and less film waste than on a car with many panels. Installers still plan for the wide rocker panels and the rear diffuser area.

Zenvo ST1 wrap ideas start with the two long side doors, which are each wrapped as one large piece of film and need a second pair of hands. The door handles and side mirrors come off for a clean edge, while the front bumper needs cut-outs for the grille and intakes. The rear diffuser and the badges are small areas that are easier with knifeless tape.

How much vinyl to wrap a Zenvo ST1 does not change between production years, because this page covers only the first generation from 2009 to 2015. A shop that counts film for this car uses the same 52 ft (16 m) estimate for every year, since the body stayed the same. Chrome or patterned film adds about 7 ft (2 m) because the pattern repeat wastes material.

Questions about wrapping a Zenvo ST1

How much vinyl does it take to wrap a Zenvo ST1?

It takes about 52 ft (16 m) of 60-inch (1.52 m) cast film to wrap a Zenvo ST1 fully. Chrome or patterned film increases the estimate to about 59 ft (18 m) because the pattern must be matched. The first generation coupe is 183.7 in (4,665 mm) long, and its two long doors each use one large piece of film.

Can I wrap only the hood or the roof of a Zenvo ST1?

Yes, you can wrap only the hood or the roof of a Zenvo ST1 as a partial wrap. The roof, hood, and mirror caps are the standard smaller jobs on this coupe. A partial wrap uses less film and time than a full color change.

Is a Zenvo ST1 hard to wrap?

Yes, a Zenvo ST1 is hard to wrap because its two long side doors are each one large piece of film that needs careful handling. The car is 183.7 in (4,665 mm) long, so a full wrap uses about 52 ft (16 m) of 60-inch (1.52 m) film. The front bumper needs cut-outs for the grille and intakes, which adds time.

How many generations of the Zenvo ST1 does this page cover?

This page covers one generation of the Zenvo ST1, the first generation produced from 2009 to 2015. There are no other generations in the catalog, so the film estimate stays the same for all years.