Wraps by car

Hanomag Typ 13 wrap

The Hanomag Typ 13 wrap page covers the 1939–1941 compact sedan, the only generation in this catalog. A full vinyl wrap of the first-generation body uses about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. With chrome or patterned film, the estimate rises to about 61 ft (18.5 m).

1generations16.5 mof film for a full wrap

Hanomag Typ 13, first generation, factory photo
Hanomag Typ 13, first generation. Factory color shown.

Hanomag Typ 13 wrap colors and ideas

  • Hanomag Typ 13 black wrap
  • Hanomag Typ 13 white wrap
  • Hanomag Typ 13 gray wrap
  • Hanomag Typ 13 silver wrap
  • Hanomag Typ 13 red wrap
  • Hanomag Typ 13 blue wrap
  • Hanomag Typ 13 green wrap
  • Hanomag Typ 13 yellow wrap
  • Hanomag Typ 13 orange wrap
  • Hanomag Typ 13 purple wrap
  • Hanomag Typ 13 pink wrap
  • Hanomag Typ 13 teal wrap
  • Hanomag Typ 13 brown wrap
  • Hanomag Typ 13 gold wrap
  • Hanomag Typ 13 chrome wrap
  • Hanomag Typ 13 color shift wrap
  • Hanomag Typ 13 carbon fiber wrap
  • Hanomag Typ 13 camo and patterned wrap

How much vinyl to wrap a Hanomag Typ 13

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1939–1941sedan (2 doors)166.5 in (4,230 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)

Hanomag Typ 13 wrap cost factors

Hanomag Typ 13 wrap cost depends on the film chosen, the condition of the paint, and the number of panels removed for installation. A full wrap on this two-door sedan needs about 54 ft (16.5 m) of cast film, while chrome or patterned film raises the amount to about 61 ft (18.5 m). Labor is also affected by the long side doors, each of which is handled as a single large piece, and by any necessary paint correction before the wrap.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).
  • Body: sedan (2 doors).
  • Two long side doors: each door is one large piece of film.

Hanomag Typ 13 wraps by generation

Swipe sideways. Tap a card for the full description.

Hanomag Typ 13, first generation, factory photo
Factory color shown

1939–1941 Hanomag Typ 13 sedan (first generation)

1939–1941sedan (2 doors)166.5 in (4,230 mm)

The first-generation Hanomag Typ 13 was produced from 1939 to 1941 as a two-door sedan. Its paint may be original or repainted, and a test spot comes before a full wrap to check adhesion on aged surfaces. The body length of 166.5 in (4,230 mm) makes it a compact car, but the long side doors remain the main challenge for a smooth installation.

Two long side doors: each door is one large piece of film.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Hanomag Typ 13

A partial wrap on a Hanomag Typ 13 can cover just the roof, hood, or mirror caps in a contrasting film. A chrome delete covers the window trim and badges with black film, leaving the painted body untouched. Paint protection film (PPF) is often applied as a clear film on the front end to guard against stone chips without changing the appearance.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Hanomag Typ 13: body, cut-outs and film

A Hanomag Typ 13 vinyl wrap works with one body style: a two-door sedan that is 166.5 in (4,230 mm) long. The two long side doors are among the largest single panels on the car and are each wrapped as one piece of film. The compact size keeps the total surface area moderate, but the tall door panels need careful squeegee work to avoid stretch marks.

Hanomag Typ 13 wrap ideas include covering the body in a single color or adding a contrasting roof. The window trim and badges can be covered in black film for a chrome delete, which changes the brightwork without repainting. Because the car has two long side doors, installing a continuous design across both doors on each side creates a smooth, uninterrupted line.

How much vinyl to wrap a Hanomag Typ 13 depends on the film type and the installer's waste factor. The catalog lists one generation, so the 54 ft (16.5 m) cast film estimate for a full wrap does not change across years. A chrome or patterned wrap needs about 61 ft (18.5 m) because pattern matching and extra trimming consume more material.

More Hanomag wraps

Questions about wrapping a Hanomag Typ 13

How much vinyl does it take to wrap a Hanomag Typ 13?

A full wrap of a Hanomag Typ 13 takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. If the wrap uses chrome or patterned film, the estimate rises to about 61 ft (18.5 m) because of additional trimming and pattern alignment. These figures cover the first-generation two-door sedan body.

Can I wrap only the hood or the roof of a Hanomag Typ 13?

Yes, you can wrap only the hood or the roof of a Hanomag Typ 13. A partial wrap on this car commonly covers the roof, hood, or mirror caps as separate jobs. A chrome delete on the window trim and badges is another option that does not require covering entire body panels.

Is a Hanomag Typ 13 hard to wrap?

A Hanomag Typ 13 is moderately hard to wrap because of its long side doors, each of which must be covered with one large piece of film. The car's compact size and simple sedan shape help overall, but those tall door panels require careful handling to avoid wrinkles and stretch marks. The age of the paint can also add preparation time if the surface is original or repainted.

How many generations of the Hanomag Typ 13 does this page cover?

This page covers one generation of the Hanomag Typ 13, produced from 1939 to 1941. The catalog lists only the first-generation two-door sedan body.