Wraps by car

Isdera Imperator 108i wrap

The Isdera Imperator 108i wrap page covers the first generation coupe produced from 1984 to 1993. A full vinyl wrap of this sports car uses about 52 ft (16 m) of 60-inch (1.52 m) cast film. Chrome or patterned film requires about 64 ft (19.5 m) due to extra material for alignment.

1generations16 mof film for a full wrap

Isdera Imperator 108i, first generation, factory photo
Isdera Imperator 108i, first generation. Factory color shown.

Isdera Imperator 108i wrap colors and ideas

  • Imperator 108i black wrap
  • Imperator 108i white wrap
  • Imperator 108i gray wrap
  • Imperator 108i silver wrap
  • Imperator 108i red wrap
  • Imperator 108i blue wrap
  • Imperator 108i green wrap
  • Imperator 108i yellow wrap
  • Imperator 108i orange wrap
  • Imperator 108i purple wrap
  • Imperator 108i pink wrap
  • Imperator 108i teal wrap
  • Imperator 108i brown wrap
  • Imperator 108i gold wrap
  • Imperator 108i chrome wrap
  • Imperator 108i color shift wrap
  • Imperator 108i carbon fiber wrap
  • Imperator 108i camo and patterned wrap

How much vinyl to wrap an Isdera Imperator 108i

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1984–1993coupe (2 doors)166.9 in (4,240 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m)

Imperator 108i wrap cost factors

Imperator 108i wrap cost depends on the amount of film, which is about 52 ft (16 m) for a standard color change. The tall body of 72.2 in (1,835 mm) means the roof is wrapped from a platform, adding labor time. A chrome or patterned film uses about 64 ft (19.5 m) of material, which increases the cost.

  • Film for a full wrap: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.
  • A tall body (72.2 in (1,835 mm)): the roof is wrapped from a platform.

Imperator 108i wraps by generation

Swipe sideways. Tap a card for the full description.

Isdera Imperator 108i, first generation, factory photo
Factory color shown

1984–1993 Imperator 108i coupe (first generation)

1984–1993coupe (2 doors)166.9 in (4,240 mm)

The first generation Isdera Imperator 108i was built from 1984 to 1993 as a coupe with two doors. Its tall body of 72.2 in (1,835 mm) means the roof is wrapped from a platform and takes more time than on a lower car. The length of 166.9 in (4,240 mm) is part of the estimate of about 52 ft (16 m) of film for a full wrap.

Two long side doors: each door is one large piece of film.

A tall body (72.2 in (1,835 mm)): the roof is wrapped from a platform.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).

Roof, hood, chrome delete and PPF on an Imperator 108i

A partial wrap on an Imperator 108i can cover the roof, hood, or mirror caps, which are smaller jobs that use less film. Chrome delete covers window trim and badges with black film instead of the bright original finish. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Isdera Imperator 108i: body, cut-outs and film

The Isdera Imperator 108i vinyl wrap starts with a coupe body that is 166.9 in (4,240 mm) long and 72.2 in (1,835 mm) tall. The two long side doors are each wrapped as one large piece of film. The tall height means the roof is wrapped from a platform, which adds time to the job.

Imperator 108i wrap ideas must account for the side doors, which are each covered with one large piece of film. The roof is wrapped from a platform because the body stands 72.2 in (1,835 mm) high. Installers remove trim around windows and badges to tuck film edges for a clean finish.

To find how much vinyl to wrap an Imperator 108i, use the estimate of about 52 ft (16 m) of 60-inch (1.52 m) cast film. Chrome or patterned film needs about 64 ft (19.5 m) because the pattern must be matched. The single generation from 1984 to 1993 has one body style, so the figure stays the same for every car.

Questions about wrapping an Isdera Imperator 108i

How much vinyl does it take to wrap an Isdera Imperator 108i?

A full wrap of an Isdera Imperator 108i takes about 52 ft (16 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, the estimate is about 64 ft (19.5 m) because the material needs extra for alignment.

Can I wrap only the hood or the roof of an Imperator 108i?

Yes, you can wrap only the hood or the roof of an Imperator 108i. A partial wrap of the roof, hood, or mirror caps is a smaller job that uses less film than a full wrap.

Is an Imperator 108i hard to wrap?

The Isdera Imperator 108i is hard to wrap because of its tall body of 72.2 in (1,835 mm), which means the roof is wrapped from a platform. The two long side doors are each one large piece of film, so installing them without wrinkles takes care. These factors add work compared to a lower car with shorter panels.

How many generations of the Imperator 108i does this page cover?

This page covers one generation of the Imperator 108i, produced from 1984 to 1993. The first generation is the only generation listed in the catalog for this model.