Wraps by car

Isdera Spyder wrap

The Isdera Spyder wrap page covers the single generation built from 1983 to 1993. A full vinyl wrap of the newest body takes about 38 ft (11.5 m) of 60-inch (1.52 m) cast film. Choose chrome or patterned film and plan on about 44 ft (13.5 m).

1generations11.5 mof film for a full wrap

Isdera Spyder, first generation, factory photo
Isdera Spyder, first generation. Factory color shown.

Isdera Spyder wrap colors and ideas

  • Spyder black wrap
  • Spyder white wrap
  • Spyder gray wrap
  • Spyder silver wrap
  • Spyder red wrap
  • Spyder blue wrap
  • Spyder green wrap
  • Spyder yellow wrap
  • Spyder orange wrap
  • Spyder purple wrap
  • Spyder pink wrap
  • Spyder teal wrap
  • Spyder brown wrap
  • Spyder gold wrap
  • Spyder chrome wrap
  • Spyder color shift wrap
  • Spyder carbon fiber wrap
  • Spyder camo and patterned wrap

How much vinyl to wrap an Isdera Spyder

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1983–1993convertible (2 doors)163.8 in (4,160 mm)about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m)

Spyder wrap cost factors

Spyder wrap cost depends on the car's single body and its dimensions. At 163.8 in (4,160 mm) long, the convertible has less surface area than a closed coupe, but the open top adds edge work. The amount of film, about 38 ft (11.5 m) of 60-inch (1.52 m) cast material, sets a base for material cost. Chrome or patterned film raises film use to about 44 ft (13.5 m), and the installer's time for cut-outs and panel alignment also affects the final cost.

  • Film for a full wrap: about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Spyder wraps by generation

Swipe sideways. Tap a card for the full description.

Isdera Spyder, first generation, factory photo
Factory color shown

1983–1993 Spyder convertible (first generation)

1983–1993convertible (2 doors)163.8 in (4,160 mm)

The open top on the first generation Spyder is not covered with wrap film. A fabric top remains unwrapped, and the vinyl ends where the fabric begins at the beltline and header. A folding hard top, if fitted, is wrapped as separate panels of its own. The film edge around the top is finished with a clean trim line.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 44 ft (13.5 m).

Roof, hood, chrome delete and PPF on a Spyder

A partial wrap on a Spyder can cover the hood, mirror caps, or rear deck alone. Spyder chrome delete replaces bright window trim and badges with black film. Paint protection film (PPF) is a clear urethane film applied to the front end for chip and scratch resistance. Each smaller job uses less film than the full 38 ft (11.5 m) estimate.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Isdera Spyder: body, cut-outs and film

An Isdera Spyder vinyl wrap deals with one body style: a two-door convertible. The car measures 163.8 in (4,160 mm) in overall length, which sets the size of the panels. With no fixed roof, the film runs continuously over the hood, doors, and rear deck. The open body reduces the number of large, curved surfaces compared to a coupe.

Spyder wrap ideas start with the convertible top itself, but the fabric or folding hard top is not wrapped. The film ends where the top begins, so the edge must be trimmed cleanly around the header and boot. A folding hard top is wrapped as panels of its own, separate from the body. Door handles, mirrors, and the rear deck area need careful cut-outs or removal.

How much vinyl to wrap a Spyder depends on the single generation cataloged here. The 1983–1993 body calls for the same film estimate, since the body dimensions are listed once. A full wrap needs about 38 ft (11.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, allow about 44 ft (13.5 m) for pattern matching and waste.

Questions about wrapping an Isdera Spyder

How much vinyl does it take to wrap an Isdera Spyder?

About 38 ft (11.5 m) of 60-inch (1.52 m) cast film wraps an Isdera Spyder. That figure covers the full body of the 1983–1993 convertible. If you pick chrome or patterned film, the estimate rises to about 44 ft (13.5 m) for matching and waste.

Is the top of a Spyder wrapped?

No, the top of a Spyder is not wrapped. A fabric top stays uncovered, and the wrap film ends where the top begins. A folding hard top is treated as separate panels and can be wrapped on its own.

Can I wrap only the hood or the roof of a Spyder?

Yes, you can wrap only the hood or the roof of a Spyder. A partial wrap covers the hood, mirror caps, or rear deck instead of the whole car. For a closed roof, the folding hard top panels are wrapped by themselves.

Is a Spyder hard to wrap?

Yes, a Spyder is a demanding wrap because of its open body. The convertible top means the film must be trimmed to a clean edge where the top begins. The 163.8 in (4,160 mm) length and mid-engine rear deck add curves that require careful stretching and relief cuts.