Wraps by car

Marlin Sportster wrap

This Marlin Sportster wrap guide covers the first-generation convertible produced from 2003 to now, and a full wrap of its body takes about 46 ft (14 m) of 60-inch (1.52 m) cast film or about 52 ft (16 m) if you choose chrome or patterned film. The page includes the film amount, the parts that need attention, and the options for partial work. Use the data here to plan a vinyl wrap for the Sportster.

1generations14 mof film for a full wrap

Marlin Sportster, first generation, factory photo
Marlin Sportster, first generation. Factory color shown.

Marlin Sportster wrap colors and ideas

  • Sportster black wrap
  • Sportster white wrap
  • Sportster gray wrap
  • Sportster silver wrap
  • Sportster red wrap
  • Sportster blue wrap
  • Sportster green wrap
  • Sportster yellow wrap
  • Sportster orange wrap
  • Sportster purple wrap
  • Sportster pink wrap
  • Sportster teal wrap
  • Sportster brown wrap
  • Sportster gold wrap
  • Sportster chrome wrap
  • Sportster color shift wrap
  • Sportster carbon fiber wrap
  • Sportster camo and patterned wrap

How much vinyl to wrap a Marlin Sportster

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2003–nowconvertible (2 doors)143.7 in (3,650 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m)

Sportster wrap cost factors

Sportster wrap cost depends on the size of the body, the film you pick, and the extra work the convertible shape adds. The car is 143.7 in (3,650 mm) long, so it uses less film than a larger sports car. A wrap in chrome or patterned film needs about 52 ft (16 m) instead of about 46 ft (14 m) for a standard color. Removing small parts like handles and mirrors adds labor.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Sportster wraps by generation

Swipe sideways. Tap a card for the full description.

Marlin Sportster, first generation, factory photo
Factory color shown

2003–now Sportster convertible (first generation)

2003–nowconvertible (2 doors)143.7 in (3,650 mm)

The open top of the first-generation Marlin Sportster is not wrapped, and the film ends where the roof opening begins. The body is a two-door convertible, so the wrap covers the doors, fenders, hood, rear deck, and bumpers. A fabric top is left as it is, while a folding hard top is wrapped as its own panels. The installers run the film to the edge of the opening and trim it neatly there.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m).

Roof, hood, chrome delete and PPF on a Sportster

A partial wrap on the Marlin Sportster can cover the hood, mirror caps, and rear deck without doing the whole body. A Sportster chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to resist stone chips. These smaller jobs use less material than a full wrap.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Marlin Sportster: body, cut-outs and film

A Marlin Sportster vinyl wrap has to handle a two-door convertible body that is 143.7 in (3,650 mm) long, so the film is cut for smaller panels than on a sedan. The rear deck and hood are large flat areas that use fewer pieces of film. The bumper and rocker panels need extra care because they follow tight curves.

Sportster wrap ideas start with the parts that need cut-outs or come off for a clean result. The door handles, mirrors, and badges are removed before the film goes on. The side marker lights and the antenna base need precise trimming around them. The windshield washer nozzles are also cut out or unmounted for the wrap.

How much vinyl to wrap a Sportster is the same for every car in this generation, because the body has not changed since 2003. A full wrap of the newest body takes about 46 ft (14 m) of 60-inch (1.52 m) cast film, and chrome or patterned film takes about 52 ft (16 m). You order one amount for any year in this generation.

More Marlin wraps

Questions about wrapping a Marlin Sportster

How much vinyl does it take to wrap a Marlin Sportster?

A full wrap of a Marlin Sportster takes about 46 ft (14 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for about 52 ft (16 m). These amounts cover the newest body of the first generation, which is the same shape from 2003 to now.

Is the top of a Sportster wrapped?

No, the top of a Sportster is not wrapped. The film ends where the top begins, and the fabric top is left uncovered. A folding hard top is wrapped as its own panels if the car has one.

Can I wrap only the hood or the roof of a Sportster?

Yes, you can wrap only the hood or the rear deck of a Sportster. A partial wrap can include the hood, mirror caps, and rear deck, so the hood alone is one option. A paint protection film on the front end is another partial choice.

Is a Sportster hard to wrap?

A Sportster is not hard to wrap if you plan for its compact size and the convertible top edge. At 143.7 in (3,650 mm) long, the panels are small and easy to handle. The extra work comes from the top opening, where the film is trimmed precisely, and from removing parts like handles and mirrors.