Wraps by car

Microcar M.Go wrap

A Microcar M.Go wrap uses vinyl film to change color or protect the paint of this mini hatchback. The first generation has run from 2009 to now, and this page covers that single generation. A full wrap of the three-door body takes about 39 ft (12 m) of 60-inch (1.52 m) cast film, or about 46 ft (14 m) if you choose chrome or patterned film.

1generations12 mof film for a full wrap

Microcar M.Go, first generation, factory photo
Microcar M.Go, first generation. Factory color shown.

Microcar M.Go wrap colors and ideas

  • M.Go black wrap
  • M.Go white wrap
  • M.Go gray wrap
  • M.Go silver wrap
  • M.Go red wrap
  • M.Go blue wrap
  • M.Go green wrap
  • M.Go yellow wrap
  • M.Go orange wrap
  • M.Go purple wrap
  • M.Go pink wrap
  • M.Go teal wrap
  • M.Go brown wrap
  • M.Go gold wrap
  • M.Go chrome wrap
  • M.Go color shift wrap
  • M.Go carbon fiber wrap
  • M.Go camo and patterned wrap

How much vinyl to wrap a Microcar M.Go

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2009–nowhatchback (3 doors)118.2 in (3,003 mm)about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m)

M.Go wrap cost factors

An M.Go wrap cost depends on the size of the area you cover, the film you choose, and how much preparation the body needs. The full car needs about 39 ft (12 m) of cast film, while partial jobs use less material. A small car like this still requires the same careful trimming around the tailgate glass and door edges, which affects the work time.

  • Film for a full wrap: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).
  • Body: hatchback (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

M.Go wraps by generation

Swipe sideways. Tap a card for the full description.

Microcar M.Go, first generation, factory photo
Factory color shown

2009–now M.Go hatchback (first generation)

2009–nowhatchback (3 doors)118.2 in (3,003 mm)

The first generation Microcar M.Go has been built since 2009, so many examples have original paint or panels that were repainted at different times. A test spot on each panel shows whether the film will hold before a full wrap. If the paint is uneven, the installer may need to clean or sand small areas first.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).

Roof, hood, chrome delete and PPF on an M.Go

You can choose a partial wrap on an M.Go: the roof, hood, or mirror caps are common smaller areas for color change film. A chrome delete covers the window trim and badges with black film, while paint protection film (PPF) is clear film on the front end. Each job uses less material than a full wrap but still needs the same careful cutting.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Microcar M.Go: body, cut-outs and film

A Microcar M.Go vinyl wrap fits a small hatchback body that is 118.2 in (3,003 mm) long with three doors. The tidy size means panels are short and many sections can be covered with offcuts. The two side doors are long enough to be one large piece each, so you need uninterrupted stretches of film.

M.Go wrap ideas start with the tailgate, where the rear glass is set into the panel and the film must end at the edge of the glass. The two long side doors each take one large piece of film, but their lower edges and handles need careful cutting. If you plan a chrome delete, the window trim and badges are small parts that can be covered with black film.

If you need to know how much vinyl to wrap an M.Go, the first generation has not changed shape since 2009, so the estimate stays the same for all years. A full wrap takes about 39 ft (12 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for about 46 ft (14 m).

Questions about wrapping a Microcar M.Go

How much vinyl does it take to wrap a Microcar M.Go?

It takes about 39 ft (12 m) of 60-inch (1.52 m) cast film to wrap a Microcar M.Go. If you use chrome or patterned film, you need about 46 ft (14 m). These figures are for the first generation body, which is the only generation in the catalog.

Can I wrap only the hood or the roof of an M.Go?

Yes, you can wrap only the hood or the roof of an M.Go. A partial wrap also includes mirror caps, a chrome delete for the window trim and badges, or clear paint protection film (PPF) on the front end.

Is an M.Go hard to wrap?

An M.Go is easy to wrap because it is a small car, but the tailgate with the rear glass in it adds work: the film must end cleanly at the edge of the glass. The two long side doors each take one large piece, so you need enough space and patience to lay the film without wrinkles.

How many generations of the M.Go does this page cover?

This page covers one generation of the M.Go, the first generation from 2009 to now. There is no second generation in the catalog.