Wraps by car

Rimac Concept One wrap

The Rimac Concept One wrap page covers the first generation of this electric sports car, produced from 2013 to 2016. A full vinyl wrap of the Concept One takes about 51 ft (15.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds roughly 6 ft (1.8 m) to the total. The car is a two-door coupe with a length of 179.1 in (4,548 mm).

1generations15.5 mof film for a full wrap

Rimac Concept One, first generation, factory photo
Rimac Concept One, first generation. Factory color shown.

Rimac Concept One wrap colors and ideas

  • Concept One black wrap
  • Concept One white wrap
  • Concept One gray wrap
  • Concept One silver wrap
  • Concept One red wrap
  • Concept One blue wrap
  • Concept One green wrap
  • Concept One yellow wrap
  • Concept One orange wrap
  • Concept One purple wrap
  • Concept One pink wrap
  • Concept One teal wrap
  • Concept One brown wrap
  • Concept One gold wrap
  • Concept One chrome wrap
  • Concept One color shift wrap
  • Concept One carbon fiber wrap
  • Concept One camo and patterned wrap

How much vinyl to wrap a Rimac Concept One

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2013–2016coupe (2 doors)179.1 in (4,548 mm)about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m)

Concept One wrap cost factors

Concept One wrap cost depends on the amount of film, the complexity of the body, and the labor involved. A full wrap of this car uses about 51 ft (15.5 m) of 60-inch (1.52 m) vinyl. The long side doors are large single pieces that require careful handling. The charge port door is a small extra piece that adds a bit of work.

  • Film for a full wrap: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.
  • Electric car: the charge port door is wrapped as a small piece of its own.

Concept One wraps by generation

Swipe sideways. Tap a card for the full description.

Rimac Concept One, first generation, factory photo
Factory color shown

2013–2016 Concept One coupe (first generation)

2013–2016coupe (2 doors)179.1 in (4,548 mm)

The first generation Rimac Concept One is a two-door coupe that is 179.1 in (4,548 mm) long. This size means the car needs about 51 ft (15.5 m) of film for a full wrap. The body has two long doors that are each wrapped with one large sheet of vinyl. The coupe styling gives the installer large, relatively flat panels for the hood, roof, and rear deck.

Two long side doors: each door is one large piece of film.

Electric car: the charge port door is wrapped as a small piece of its own.

Film: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).

Roof, hood, chrome delete and PPF on a Concept One

A partial wrap on a Rimac Concept One can cover the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear layer applied to the front end to guard against stone chips. These smaller jobs use less film than a full color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Rimac Concept One: body, cut-outs and film

A Rimac Concept One vinyl wrap suits the coupe body of the car, with its two long side doors. Each door is covered with one large piece of film, which reduces the number of visible seams. The overall length of 179.1 in (4,548 mm) means a full wrap uses about 51 ft (15.5 m) of film. The body shape has no sharp corners that would require extra relief cuts.

Concept One wrap ideas include covering the two long side doors as single panels for a clean look. The charge port door is wrapped as a small separate piece so it can open without stretching the main film. Window trim and badges can be covered with black film for a chrome delete. The coupe shape allows the roof and hood to be wrapped as individual panels.

How much vinyl to wrap a Concept One depends on the single generation of the car. The first generation from 2013 to 2016 uses the same body style and length across all years. A full color change wrap takes about 51 ft (15.5 m) of standard cast film. If you choose chrome or patterned film, plan for about 57 ft (17.5 m) because of the extra material needed for matching.

Questions about wrapping a Rimac Concept One

How much vinyl does it take to wrap a Rimac Concept One?

It takes about 51 ft (15.5 m) of vinyl to wrap a Rimac Concept One. This figure is for a full color change wrap using 60-inch (1.52 m) cast film. If you use chrome or patterned film, the amount rises to about 57 ft (17.5 m).

Can I wrap only the hood or the roof of a Concept One?

Yes, you can wrap only the hood or the roof of a Concept One. A partial wrap often covers the roof, hood, or mirror caps. The coupe body allows these panels to be wrapped separately from the rest of the car.

Is a Concept One hard to wrap?

A Concept One is not the easiest car to wrap because of its size and electric car features. The long side doors are large single pieces that need careful handling to avoid wrinkles. The charge port door is wrapped as a small separate piece, which adds a step. The overall length of 179.1 in (4,548 mm) means more film and more alignment work.

How many generations of the Concept One does this page cover?

This page covers one generation of the Concept One. The first generation was produced from 2013 to 2016. All Concept One models on this page share the same body style and film estimate.