Wraps by car

Rimac Nevera wrap

The Rimac Nevera wrap page covers the first generation of this electric coupe, produced from 2021 to the present. A full wrap of the newest body takes about 52 ft (16 m) of 60-inch (1.52 m) cast vinyl film. Chrome or patterned film increases the amount to about 59 ft (18 m).

1generations16 mof film for a full wrap

Rimac Nevera, first generation, factory photo
Rimac Nevera, first generation. Factory color shown.

Rimac Nevera wrap colors and ideas

  • Nevera black wrap
  • Nevera white wrap
  • Nevera gray wrap
  • Nevera silver wrap
  • Nevera red wrap
  • Nevera blue wrap
  • Nevera green wrap
  • Nevera yellow wrap
  • Nevera orange wrap
  • Nevera purple wrap
  • Nevera pink wrap
  • Nevera teal wrap
  • Nevera brown wrap
  • Nevera gold wrap
  • Nevera chrome wrap
  • Nevera color shift wrap
  • Nevera carbon fiber wrap
  • Nevera camo and patterned wrap

How much vinyl to wrap a Rimac Nevera

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2021–nowcoupe (2 doors)187.0 in (4,750 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m)

Nevera wrap cost factors

Nevera wrap cost depends on the amount of film, which is about 52 ft (16 m) for the full body in standard cast vinyl. Chrome or patterned film raises the material amount to about 59 ft (18 m). The two large door panels and the separate charge port door add labor time.

  • Film for a full wrap: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.
  • Electric car: the charge port door is wrapped as a small piece of its own.

Nevera wraps by generation

Swipe sideways. Tap a card for the full description.

Rimac Nevera, first generation, factory photo
Factory color shown

2021–now Nevera coupe (first generation)

2021–nowcoupe (2 doors)187.0 in (4,750 mm)

The first-generation Rimac Nevera is a mid-size coupe measuring 187.0 in (4,750 mm) long. This size means a full wrap uses about 52 ft (16 m) of 60-inch (1.52 m) cast film. The two long doors are each covered with one large piece of film. The charge port door is wrapped as a small separate piece.

Two long side doors: each door is one large piece of film.

Electric car: the charge port door is wrapped as a small piece of its own.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m).

Roof, hood, chrome delete and PPF on a Nevera

A partial wrap on the Rimac Nevera can cover the roof, hood, or mirror caps. Nevera chrome delete covers window trim and badges with black film. Paint protection film (PPF) is an option for the front end as a clear protective layer.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Rimac Nevera: body, cut-outs and film

The Rimac Nevera vinyl wrap is shaped by the car's mid-size coupe body and 187.0 in (4,750 mm) length. Two long side doors mean each door is wrapped as one large piece of film. The smooth body lines reduce the number of separate panels.

Nevera wrap ideas start with the long side doors, which are large single pieces that need careful alignment. The charge port door is wrapped as its own small piece because this is an electric car. The installer cuts around badges and sensors rather than removing them.

How much vinyl to wrap a Nevera stays constant because only one generation is in this catalog. The first generation from 2021 onward uses the same body dimensions and panel layout. There is no earlier or later body to compare for film estimates.

Questions about wrapping a Rimac Nevera

How much vinyl does it take to wrap a Rimac Nevera?

Yes, it takes about 52 ft (16 m) of 60-inch (1.52 m) cast vinyl to wrap a Rimac Nevera. Chrome or patterned film requires about 59 ft (18 m) because of extra material for alignment.

Can I wrap only the hood or the roof of a Nevera?

Yes, a partial wrap can cover only the hood or the roof of a Nevera. Other partial options are mirror caps, chrome delete for window trim and badges, and clear paint protection film on the front end.

Is a Nevera hard to wrap?

Yes, a Nevera is harder to wrap than a smaller car because of its 187.0 in (4,750 mm) length and two long doors. Each door needs one large piece of film without seams, and the charge port door is wrapped as a separate small piece.

How many generations of the Nevera does this page cover?

This page covers one generation of the Rimac Nevera. The first generation has been produced from 2021 to the present as a mid-size coupe.