Wraps by car

Linxys g105 wrap

The Linxys g105 wrap page covers the first-generation minivan produced from 2024 to now, the only generation in the catalog. A full vinyl wrap of this newest body takes about 66 ft (20 m) of 60-inch (1.52 m) cast film. That film estimate covers the standard color change wrap on the whole exterior. The Linxys g105 is an electric minivan with a tall body and sliding doors.

1generations20 mof film for a full wrap

Linxys g105, first generation, factory photo
Linxys g105, first generation. Factory color shown.

Linxys g105 wrap colors and ideas

  • Linxys g105 black wrap
  • Linxys g105 white wrap
  • Linxys g105 gray wrap
  • Linxys g105 silver wrap
  • Linxys g105 red wrap
  • Linxys g105 blue wrap
  • Linxys g105 green wrap
  • Linxys g105 yellow wrap
  • Linxys g105 orange wrap
  • Linxys g105 purple wrap
  • Linxys g105 pink wrap
  • Linxys g105 teal wrap
  • Linxys g105 brown wrap
  • Linxys g105 gold wrap
  • Linxys g105 chrome wrap
  • Linxys g105 color shift wrap
  • Linxys g105 carbon fiber wrap
  • Linxys g105 camo and patterned wrap

How much vinyl to wrap a Linxys g105

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2024–nowvan (4 doors)178.1 in (4,525 mm)about 66 ft (20 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m)

Linxys g105 wrap cost factors

The Linxys g105 wrap cost depends on the amount of film needed, which is about 66 ft (20 m) for a standard color change and about 76 ft (23 m) for chrome or patterned film. The labor is higher because of the sliding door tracks, which must be cut around carefully, and the tall body requires a platform for the roof. The charge port door adds a small separate piece of film. A partial wrap on the roof, hood, or mirror caps uses less material and less time than a full wrap.

  • Film for a full wrap: about 66 ft (20 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m).
  • Body: van (4 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.
  • Electric car: the charge port door is wrapped as a small piece of its own.
  • A tall body (74.8 in (1,900 mm)): the roof is wrapped from a platform.

Linxys g105 wraps by generation

Swipe sideways. Tap a card for the full description.

Linxys g105, first generation, factory photo
Factory color shown

2024–now Linxys g105 van (first generation)

2024–nowvan (4 doors)178.1 in (4,525 mm)

The first-generation Linxys g105, produced from 2024 to now, has sliding side doors with tracks that stay bare and decide where the film is cut. This means the installer cannot wrap over the tracks, so the film edge is placed along the opening. The tall body, at 74.8 in (1,900 mm), also means the roof wrap is done from a platform. These factors are specific to this generation and affect the wrapping process.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Electric car: the charge port door is wrapped as a small piece of its own.

A tall body (74.8 in (1,900 mm)): the roof is wrapped from a platform.

Film: about 66 ft (20 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 76 ft (23 m).

Roof, hood, chrome delete and PPF on a Linxys g105

A partial wrap on a Linxys g105 can cover the roof, hood, or mirror caps instead of the whole van. For a Linxys g105 chrome delete, the window trim and badges are covered with black film to change the look. Paint protection film (PPF) is another option, with clear film applied to the front end to guard against stone chips. These smaller jobs use less film than a full wrap and can be done without wrapping the sliding doors.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Linxys g105: body, cut-outs and film

The Linxys g105 vinyl wrap has to cover a van body that is 178.1 in (4,525 mm) long and 74.8 in (1,900 mm) tall. The single body style is a four-door van with sliding side doors, so the installer works around the door tracks and leaves them bare. Because the roof is high, wrapping it safely requires a platform or step. The large flat side panels take film well, but the sliding door areas need precise cutting.

For Linxys g105 wrap ideas, the sliding side doors are the main point to plan around, because the tracks stay bare and the film is cut along them. The charge port door on this electric car is wrapped as a small separate piece for a clean finish. The tall body means the roof is wrapped from a platform, which adds labor but gives a complete look. Owners can choose a full color change, a partial wrap, or a chrome delete on the window trim and badges.

To know how much vinyl to wrap a Linxys g105, you use the figure of about 66 ft (20 m) of 60-inch (1.52 m) cast film for a standard color change. If you pick chrome or patterned film, the estimate is about 76 ft (23 m) because of more waste in matching the pattern. The first generation, from 2024 to now, is the only body style in the catalog, so the figure stays the same. For partial jobs like the hood and roof, you need less film, but the installer calculates from the same roll width.

Questions about wrapping a Linxys g105

How much vinyl does it take to wrap a Linxys g105?

A Linxys g105 needs about 66 ft (20 m) of 60-inch (1.52 m) vinyl for a full wrap, and about 76 ft (23 m) if you use chrome or patterned film. The standard figure covers a color change wrap on the whole van. The extra for chrome or patterned film comes from the need to match patterns across panels.

Are the sliding doors of a Linxys g105 wrapped?

Yes, the sliding doors of a Linxys g105 are wrapped, but the door tracks stay bare. The film is cut along the tracks so the doors can slide freely. This is a key step in a full wrap of this van.

Can I wrap only the hood or the roof of a Linxys g105?

Yes, you can wrap only the hood or the roof of a Linxys g105 as a partial wrap. The roof, hood, and mirror caps are common partial wrap areas. A partial wrap uses less material than a full wrap.

Is a Linxys g105 hard to wrap?

Yes, a Linxys g105 is harder to wrap than a standard sedan because of its sliding door tracks and tall body. The tracks must be left bare and the film cut precisely along them, which takes extra time. The roof is 74.8 in (1,900 mm) high, so the installer needs a platform to reach it. The charge port door also adds a small separate piece of film.