To wrap a car hood, lay cast film on the panel, squeegee from the center and tuck edges. The roof follows the same method and is even flatter, which makes both panels the place to start. Each needs only a few meters of film, so a mistake costs one panel, not a car.
Key facts
- The film calculator estimates 3 m (10 ft) of cast film for a sedan hood.
- By the site's estimate, a sedan roof takes 3.5 m (11 ft) of cast film.
- An SUV roof takes 4.5 m (15 ft) of cast film, its hood 2.5 m (8 ft).
- On a 1.37 m (54 in) or 1.22 m (48 in) roll, wide panels may need a seam.
Why the hood and roof come first
The hood and roof are large, mostly flat panels with few recesses. Both let you learn glassing, squeegee pressure and edge work without fighting deep curves. Mistakes are easy to see, and a spoiled piece wastes only one panel of film.
Hood wrap and roof wrap jobs also stand on their own as styling choices. A gloss black roof or a carbon fiber hood changes a car's look with little film. The visualizer on this site shows 191 wrap looks on different body types.
How much film a hood or roof needs
Film for a single panel depends on body type, panel size and roll width. The figures below come from the film calculator on this site and include spare for one re-cut. Each is an estimate on a 1.52 m (60 in) roll, not a cutting plan.
On a narrower roll, a wide hood or roof may need two strips with a seam between them. Carbon fiber and other directional films cannot be rotated to save film.
| Body type | Roof, cast film | Hood, cast film |
|---|---|---|
| City car | 3.5 m (11 ft) | 2 m (7 ft) |
| Hatchback | 4 m (13 ft) | 2.5 m (8 ft) |
| Sedan | 3.5 m (11 ft) | 3 m (10 ft) |
| Coupe | 3 m (10 ft) | 3 m (10 ft) |
| Convertible | no fixed roof | 3 m (10 ft) |
| Wagon | 5 m (16 ft) | 2.5 m (8 ft) |
| SUV | 4.5 m (15 ft) | 2.5 m (8 ft) |
| Off-roader | 4.5 m (15 ft) | 2.5 m (8 ft) |
| Pickup | 3.5 m (11 ft) | 3 m (10 ft) |
| Minivan | 6 m (20 ft) | 2 m (7 ft) |
| Van | 10.5 m (34 ft) | 2.5 m (8 ft) |
How to wrap a car hood, panel steps
Open the hood and clean it on both faces, including the underside lip. Remove washer jets or badges that sit in the panel if they come off safely. Degrease the surface last, just before the film goes on.
The front edge of the hood curves the most, so work it last with gentle heat. Edges folded under the lip resist lifting far better than film trimmed flush with the edge.
- Lay the sheet over the hood with spare overhanging on every side.
- Glass the film so it floats flat above the paint, then anchor the center.
- Squeegee outward from the center in overlapping strokes toward each edge.
- Trim the film with spare left to fold under the edges.
- Wrap the edges under the hood lip and post-heat them firmly.
How to wrap a car roof
A roof is flatter than a hood but harder to reach and handle alone. Two people, or wrap magnets, keep the large sheet off the paint while you position it. A step platform on both sides of the car lets you squeegee to the center.
Roof edges meet rubber seals, drip channels and sometimes roof rails or an antenna. Tuck the film under seals with a plastic tuck tool rather than cutting near them. A sunroof or panoramic glass leaves only a frame of paint, which needs careful knifeless tape cuts.
Hood wrap designs and black roof wraps
Hood wrap ideas range from a plain color to carbon fiber or a contrast stripe. The catalog lists 106 carbon fiber films and 42 forged carbon films for that look. A matte or satin hood in a dark shade is another option that cuts glare.
A black roof wrap gives a floating-roof look against a lighter body color. The catalog holds 285 black wrap films, so finish and shade can be matched closely. Pick a roof color that works with the window trim and roof rails.
Hood wrap for a truck or SUV
A truck hood is larger and often taller, with vents, scoops or a raised center section. Scoops and vents may need inlays, like the recesses on a bumper. The film calculator gives 3 m (10 ft) of cast film for a pickup hood.
Hoods on every car face sun and stone chips more than vertical panels do. Paint with chips or peeling clear coat must be repaired first, as the damaged paint guide explains.
Questions
Can you apply car wrap yourself?
Yes, and the hood or roof is the right first panel for it. Both are large and flat, so you learn the method without deep curves. The guide on wrapping a car yourself covers the full job.
How expensive is it to put a wrap on a car?
The cost of a wrap depends on how much you cover, the film and the labor. A hood or roof alone uses a fraction of the film a full wrap needs. Chrome and patterned films take more film and more care than plain colors.
How much to wrap the roof of a SUV?
An SUV roof takes 4.5 m (15 ft) of cast film by the site's film calculator. The labor depends on roof rails, a sunroof and the antenna. Any cost quote follows from that film amount and the work involved.
Can you wrap a hood in carbon fiber?
Yes, carbon fiber film suits a hood and goes on like any other cast film. The weave must run straight along the hood, so the piece cannot be rotated to save film. The catalog lists 106 carbon fiber films to compare in weave and finish.
Films from this guide


