Wraps by car

Bristol Fighter wrap

This page covers the Bristol Fighter wrap and the vinyl wrap film its body needs. The Bristol Fighter was produced from 2004 to 2011 in a single generation. A full wrap of the coupe body takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film. With chrome or patterned film the estimate is about 61 ft (18.5 m).

1generations14.5 mof film for a full wrap

Bristol Fighter, first generation, factory photo
Bristol Fighter, first generation. Factory color shown.

Bristol Fighter wrap colors and ideas

  • Fighter black wrap
  • Fighter white wrap
  • Fighter gray wrap
  • Fighter silver wrap
  • Fighter red wrap
  • Fighter blue wrap
  • Fighter green wrap
  • Fighter yellow wrap
  • Fighter orange wrap
  • Fighter purple wrap
  • Fighter pink wrap
  • Fighter teal wrap
  • Fighter brown wrap
  • Fighter gold wrap
  • Fighter chrome wrap
  • Fighter color shift wrap
  • Fighter carbon fiber wrap
  • Fighter camo and patterned wrap

How much vinyl to wrap a Bristol Fighter

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2004–2011coupe (3 doors)174.0 in (4,420 mm)about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m)

Fighter wrap cost factors

The Fighter wrap cost depends on the film type, the amount of film, and the labor of the install. The coupe body needs about 48 ft (14.5 m) of 60-inch (1.52 m) cast film for a full color change. Chrome or patterned film raises the material to about 61 ft (18.5 m). The two long doors are wrapped as single pieces, which adds time but saves film.

  • Film for a full wrap: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).
  • Body: coupe (3 doors).
  • Two long side doors: each door is one large piece of film.

Fighter wraps by generation

Swipe sideways. Tap a card for the full description.

Bristol Fighter, first generation, factory photo
Factory color shown

2004–2011 Fighter coupe (first generation)

2004–2011coupe (3 doors)174.0 in (4,420 mm)

The first generation Bristol Fighter dates from 2004 to 2011 and is the only body this page covers. On a car of these years the paint may be original or repainted, so a test spot of film goes on before the full wrap. The installer checks the paint for lifting or cracks and cleans any wax before laying the film. The wrap process is the same for every trim because the body shell did not change.

Two long side doors: each door is one large piece of film.

Film: about 48 ft (14.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 61 ft (18.5 m).

Roof, hood, chrome delete and PPF on a Fighter

A partial wrap on a Bristol Fighter can cover the roof, hood, or mirror caps with one color of film. A Fighter chrome delete uses black film over the window trim and badges instead of a full color change. Paint protection film (PPF) is a clear film that covers the front end only, from the bumper to the hood edge. These smaller jobs leave the doors and rear quarters in the original paint.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Bristol Fighter: body, cut-outs and film

The Bristol Fighter vinyl wrap follows the shape of a two-door coupe with a length of 174.0 in (4,420 mm). Its single body style is a three-door coupe, so the wrap covers the roof, quarter panels, and tailgate as one continuous run. The long hood and doors use wide film pieces that reduce the number of seams. The wrap installer works around the rear hatch and the side windows with careful trimming.

Fighter wrap ideas usually start with the two long side doors because each one is a single large piece of film. The door handles and mirrors come off for a clean edge, and the window trim needs a chrome delete if the owner wants black trim. The badges are removed for wrapping and then reinstalled. Cut-outs are needed for the door locks, fuel filler, and any parking sensors.

To know how much vinyl to wrap a Fighter you only count one generation because the car was built from 2004 to 2011 without a body change. A color change wrap uses about 48 ft (14.5 m) of 60-inch (1.52 m) film. If the owner chooses chrome or patterned film the estimate rises to about 61 ft (18.5 m). The installer measures the car before cutting because the coupe has no spoiler or wide arches.

Questions about wrapping a Bristol Fighter

How much vinyl does it take to wrap a Bristol Fighter?

A Bristol Fighter takes about 48 ft (14.5 m) of 60-inch (1.52 m) cast film for a full wrap. If the film is chrome or patterned the figure is about 61 ft (18.5 m). The car has one body style, a three-door coupe, so the estimate covers every Fighter from 2004 to 2011.

Can I wrap only the hood or the roof of a Fighter?

Yes, you can wrap only the hood or the roof of a Fighter. A partial wrap covers just those panels, and a roof wrap can be done without touching the doors. The hood is a single large piece that stretches from the cowl to the nose. Mirror caps can also be wrapped on their own.

Is a Fighter hard to wrap?

Yes, a Fighter adds work because of its long doors and the size of the film panels. The two side doors are each one large piece of film, so the installer needs a second pair of hands to lay them without wrinkles. The car is 174.0 in (4,420 mm) long, which means the roof and hood pieces are cut from a 60-inch (1.52 m) roll with no seams. The coupe shape has no sharp edges, but the rear hatch needs careful trimming around the glass.

How many generations of the Fighter does this page cover?

This page covers one generation of the Bristol Fighter. The car was built from 2004 to 2011 with the same coupe body. There are no other generations in the catalog.