Wraps by car

Innocenti Mini wrap

The Innocenti Mini wrap page covers the first generation built from 1965 to 1974. A full vinyl wrap of the hatchback body uses about 36 ft (11 m) of 60-inch (1.52 m) cast film. Chrome or patterned film takes about 48 ft (14.5 m) because of extra material for trimming and matching.

1generations11 mof film for a full wrap

Innocenti Mini, first generation, factory photo
Innocenti Mini, first generation. Factory color shown.

Innocenti Mini wrap colors and ideas

  • Mini black wrap
  • Mini white wrap
  • Mini gray wrap
  • Mini silver wrap
  • Mini red wrap
  • Mini blue wrap
  • Mini green wrap
  • Mini yellow wrap
  • Mini orange wrap
  • Mini purple wrap
  • Mini pink wrap
  • Mini teal wrap
  • Mini brown wrap
  • Mini gold wrap
  • Mini chrome wrap
  • Mini color shift wrap
  • Mini carbon fiber wrap
  • Mini camo and patterned wrap

How much vinyl to wrap an Innocenti Mini

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1965–1974hatchback (3 doors)123.4 in (3,135 mm)about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m)

Mini wrap cost factors

Mini wrap cost depends on body size, film choice, and how much disassembly the job needs. The Innocenti Mini is 123.4 in (3,135 mm) long, which sets the base amount of film at about 36 ft (11 m) for a full wrap. Chrome or patterned film raises the material figure to about 48 ft (14.5 m) and adds time for alignment. Anyone counting film should also allow for the two long doors and the tailgate glass that interrupt the surface.

  • Film for a full wrap: about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).
  • Body: hatchback (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

Mini wraps by generation

Swipe sideways. Tap a card for the full description.

Innocenti Mini, first generation, factory photo
Factory color shown

1965–1974 Mini hatchback (first generation)

1965–1974hatchback (3 doors)123.4 in (3,135 mm)

The first generation Innocenti Mini was built from 1965 to 1974 as a three-door hatchback. On a car of these years panels may be original or repainted, so a test spot comes before a full wrap. The painted surfaces on this body are the two long side doors, the roof, the hood, and the tailgate around the glass. The wrap film must be applied carefully over any repairs or older paint to avoid lifting.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).

Roof, hood, chrome delete and PPF on a Mini

A partial wrap on an Innocenti Mini can cover the roof, hood, and mirror caps without wrapping the whole car. Mini chrome delete covers the window trim and badges with black film for a clean look. Paint protection film (PPF) is a clear film option for the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Innocenti Mini: body, cut-outs and film

An Innocenti Mini vinyl wrap follows a three-door hatchback body that is 123.4 in (3,135 mm) long. The short length reduces the amount of film compared with larger cars, while the tall roof and upright sides keep the panels easy to work. Each of the two long side doors is wrapped as one large piece, so fewer seams are needed. A tailgate that includes the rear glass means the film stops at the edge of the glass.

Mini wrap ideas start with the cut-outs and parts that come off for a clean install. The tailgate glass interrupts the rear panel, so the film ends neatly at its edge. The two side doors are long and take one piece each, which calls for careful stretching and trimming. Door handles and badges are removed before wrapping, then reinstalled.

How much vinyl to wrap a Mini depends on the generation, but this page covers only one generation. Between 1965 and 1974 the body style stayed a three-door hatchback with a length of 123.4 in (3,135 mm). A full wrap of this body uses about 36 ft (11 m) of standard cast film, or about 48 ft (14.5 m) for chrome or patterned film.

Questions about wrapping an Innocenti Mini

How much vinyl does it take to wrap an Innocenti Mini?

It takes about 36 ft (11 m) of 60-inch (1.52 m) cast film to wrap an Innocenti Mini. For chrome or patterned film the estimate is about 48 ft (14.5 m). These figures are for the first generation hatchback body built from 1965 to 1974.

Can I wrap only the hood or the roof of a Mini?

Yes, you can wrap only the hood or the roof of a Mini as a partial job. A partial wrap on this car also covers mirror caps, while a chrome delete covers window trim and badges. Paint protection film (PPF) is another option limited to the front end.

Is a Mini hard to wrap?

A Mini is not the easiest car to wrap because of its small size and some details. The tailgate with the rear glass in it means the film ends at the edge of the glass, so trimming must be exact. The two long side doors are each wrapped as one large piece, which adds work in stretching and positioning. The car is 123.4 in (3,135 mm) long, so tight curves around the short body also require care.

How many generations of the Mini does this page cover?

This page covers one generation of the Innocenti Mini, the first generation from 1965 to 1974.