Wraps by car

Packard Clipper wrap

This Packard Clipper wrap page covers the single generation of the 1941–1947 Packard Clipper. A full vinyl wrap of the four-door sedan body takes about 64 ft (19.5 m) of 60-inch (1.52 m) cast film. The extra chrome trim on this car raises the estimate to about 74 ft (22.5 m) when covered with film.

1generations19.5 mof film for a full wrap

Packard Clipper, first generation, factory photo
Packard Clipper, first generation. Factory color shown.

Packard Clipper wrap colors and ideas

  • Clipper black wrap
  • Clipper white wrap
  • Clipper gray wrap
  • Clipper silver wrap
  • Clipper red wrap
  • Clipper blue wrap
  • Clipper green wrap
  • Clipper yellow wrap
  • Clipper orange wrap
  • Clipper purple wrap
  • Clipper pink wrap
  • Clipper teal wrap
  • Clipper brown wrap
  • Clipper gold wrap
  • Clipper chrome wrap
  • Clipper color shift wrap
  • Clipper carbon fiber wrap
  • Clipper camo and patterned wrap

How much vinyl to wrap a Packard Clipper

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1941–1947sedan (4 doors)208.5 in (5,296 mm)about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m)

Clipper wrap cost factors

Clipper wrap cost depends mainly on the size of the car body and the amount of chrome trim covered. At 208.5 in (5,296 mm) long, the sedan needs about 64 ft (19.5 m) of 60-inch (1.52 m) film for the painted panels, and the chrome raises that to about 74 ft (22.5 m). The condition of the paint and straightness of the panels also affect the time and materials for the installer.

  • Film for a full wrap: about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m).
  • Body: sedan (4 doors).

Clipper wraps by generation

Swipe sideways. Tap a card for the full description.

Packard Clipper, first generation, factory photo
Factory color shown

1941–1947 Clipper sedan (first generation)

1941–1947sedan (4 doors)208.5 in (5,296 mm)

The first generation Packard Clipper has paint age to check before any wrap begins. Panels on a 1941–1947 car may be original lacquer or repainted in different spots, so a test spot of adhesive is done on each area. Paint that is cracked, checked, or loose must be stabilized before the film goes down.

Film: about 64 ft (19.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m).

Roof, hood, chrome delete and PPF on a Clipper

A partial wrap on a Packard Clipper covers the roof, hood, or mirror caps without film on the whole car. A Clipper chrome delete uses black film on the window trim and badges to change the look of the bright parts. Paint protection film (PPF) is clear film on the front end to guard the leading edge of the long hood from stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Packard Clipper: body, cut-outs and film

The Packard Clipper vinyl wrap starts with a large four-door sedan that measures 208.5 in (5,296 mm) long. That single body style simplifies patterning but the long roof and straight panels still need careful film layout. The wrap must cover the tall greenhouse and the rear fender skirts without bridging the panel gaps.

Clipper wrap ideas include cutting around the hood ornament, door handles, and the wide chrome side trim. The bumpers, grille, and most bright parts stay on the car, while the film is knifeless-taped at the edges. The window trim and badges can be covered with black film for a chrome delete.

To know how much vinyl to wrap a Clipper, the count is the same for every car because only the first generation exists. The 1941–1947 sedan panels are the same shape across those years, so the film estimate does not change between production dates. The only difference for film use is whether the chrome trim gets wrapped or left bare.

Questions about wrapping a Packard Clipper

How much vinyl does it take to wrap a Packard Clipper?

A full wrap of a Packard Clipper takes about 64 ft (19.5 m) of 60-inch (1.52 m) cast film for the painted body panels. When the chrome trim and patterned areas are also covered, the figure rises to about 74 ft (22.5 m) of film. These numbers cover the four-door sedan body of the 1941–1947 generation.

Can I wrap only the hood or the roof of a Clipper?

Yes, a partial wrap on a Clipper covers only the roof, hood, or mirror caps as separate jobs. The roof is the largest single panel on the sedan, and the hood is a long flat surface that is easy to film in one piece. A chrome delete is also a partial job that wraps only the window trim and badges in black film.

Is a Clipper hard to wrap?

A Clipper is more work to wrap than a modern car of the same length because of the aged paint and thick chrome trim. The 208.5 in (5,296 mm) long sedan has large, flat sections that are simple to cover, but the many bright parts need precise cut-outs or removal for a clean edge. Paint that is original from 1941–1947 often needs a test spot and careful cleaning before the vinyl is applied.

How many generations of the Clipper does this page cover?

This page covers one generation of the Packard Clipper, the 1941–1947 model run. The catalog does not list any other Clipper generations, and all body information applies to those seven years. The single generation has one body style, a four-door sedan measuring 208.5 in (5,296 mm) long.