Wraps by car

PGO Hemera wrap

The PGO Hemera wrap page covers the coupe built from 2009 to now, the single generation in the catalog, and the roughly 41 ft (12.5 m) of 60-inch (1.52 m) cast vinyl wrap a full exterior needs.

1generations12.5 mof film for a full wrap

PGO Hemera, first generation, factory photo
PGO Hemera, first generation. Factory color shown.

PGO Hemera wrap colors and ideas

  • Hemera black wrap
  • Hemera white wrap
  • Hemera gray wrap
  • Hemera silver wrap
  • Hemera red wrap
  • Hemera blue wrap
  • Hemera green wrap
  • Hemera yellow wrap
  • Hemera orange wrap
  • Hemera purple wrap
  • Hemera pink wrap
  • Hemera teal wrap
  • Hemera brown wrap
  • Hemera gold wrap
  • Hemera chrome wrap
  • Hemera color shift wrap
  • Hemera carbon fiber wrap
  • Hemera camo and patterned wrap

How much vinyl to wrap a PGO Hemera

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2009–nowcoupe (2 doors)147.0 in (3,735 mm)about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m)

Hemera wrap cost factors

Hemera wrap cost depends on film choice, paint condition, and the number of panels done. A full color change on this 147.0 in (3,735 mm) coupe takes about 41 ft (12.5 m) of 60-inch (1.52 m) cast film, and a chrome or patterned film raises the amount to about 46 ft (14 m). Removing trim for a clean install on the two long doors and the window surrounds adds labor. A partial wrap on the roof, hood, or mirror caps keeps material and prep time low, while paint protection film on the front end follows the same body lines.

  • Film for a full wrap: about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Hemera wraps by generation

Swipe sideways. Tap a card for the full description.

PGO Hemera, first generation, factory photo
Factory color shown

2009–now Hemera coupe (first generation)

2009–nowcoupe (2 doors)147.0 in (3,735 mm)

The first generation of the PGO Hemera, built from 2009 to now, is the only body this page covers. On a car of these years panels may be original or repainted, and a test spot comes before a full wrap to confirm the film holds. The coupe shape and 147.0 in (3,735 mm) length stay the same through the run, so material figures do not change between early and late cars.

Two long side doors: each door is one large piece of film.

Film: about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).

Roof, hood, chrome delete and PPF on a Hemera

The PGO Hemera takes partial wrap jobs on the roof, hood, and mirror caps when a full color change is not needed. A chrome delete covers the window trim and badges with black film for a cleaner look. Paint protection film (PPF) on the front end adds a clear layer to the nose and hood without hiding the color. Each of these options uses less film than the full 41 ft (12.5 m) of 60-inch (1.52 m) vinyl wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a PGO Hemera: body, cut-outs and film

A PGO Hemera vinyl wrap suits a compact two-door sports car that is 147.0 in (3,735 mm) long. The small body and coupe shape leave no long roof or trunk panels to work around. Each of the two long side doors takes one large piece of film, which keeps seams away from the middle of the door. The modest overall size brings the material for a full wrap to about 41 ft (12.5 m) of 60-inch (1.52 m) film.

Hemera wrap ideas start with the two long doors, each covered with a single large panel of cast film. The window surrounds and badges suit a chrome delete, where bright trim is covered with black film. For clear protection, paint protection film (PPF) on the front end guards the nose and hood against stone chips. Mirror caps and the roof make a fast partial wrap that changes the car with little material.

How much vinyl to wrap a Hemera depends on the single production run from 2009 to now. The coupe has one body length of 147.0 in (3,735 mm) across those years, so the roughly 41 ft (12.5 m) figure holds for every car in the catalog. A patterned or chrome film calls for about 46 ft (14 m) because the design needs aligned overlaps. Paint age still varies on a car of these years, so a test spot before the full wrap is the safe way to check adhesion.

Questions about wrapping a PGO Hemera

How much vinyl does it take to wrap a PGO Hemera?

A PGO Hemera takes about 41 ft (12.5 m) of 60-inch (1.52 m) vinyl film for a full wrap. A chrome or patterned film needs about 46 ft (14 m) because the pattern has to be matched across panels. The estimate covers the 147.0 in (3,735 mm) coupe with its two long doors.

Can I wrap only the hood or the roof of a Hemera?

Yes, a Hemera can be wrapped only on the hood or the roof. A partial wrap on the roof, hood, or mirror caps is a standard job smaller than a full vinyl wrap. The two-piece hood and long doors are not involved, so the installer can work with offcuts from a 60-inch (1.52 m) roll.

Is a Hemera hard to wrap?

A Hemera is not hard to wrap, but the two long side doors add work because each door needs one large piece of film without seams. The 147.0 in (3,735 mm) body is compact, but the doors are tall enough that a second pair of hands helps during the wet application. The coupe shape has no separate trunk, so the rear panel is simple. The main caution is the paint: on a car from 2009 onward a test spot before the full wrap is the safe step.

How many generations of the Hemera does this page cover?

This page covers one generation of the PGO Hemera: the first and only one, built from 2009 to now. The catalog shows the coupe with two doors and a length of 147.0 in (3,735 mm) as the sole body. Every figure on the page applies to that car.