Wraps by car

PGO Speedster II wrap

A PGO Speedster II wrap covers the first-generation convertible, a small sports car built from 2005 to now. A vinyl wrap on this car needs about 38 ft (11.5 m) of 60-inch (1.52 m) cast film for a full color change. Chrome or patterned film adds waste and uses about 48 ft (14.5 m) of the same roll width. The Speedster II is a retro-styled two-seater with a body that suits a full wrap.

1generations11.5 mof film for a full wrap

PGO Speedster II, first generation, factory photo
PGO Speedster II, first generation. Factory color shown.

PGO Speedster II wrap colors and ideas

  • Speedster II black wrap
  • Speedster II white wrap
  • Speedster II gray wrap
  • Speedster II silver wrap
  • Speedster II red wrap
  • Speedster II blue wrap
  • Speedster II green wrap
  • Speedster II yellow wrap
  • Speedster II orange wrap
  • Speedster II purple wrap
  • Speedster II pink wrap
  • Speedster II teal wrap
  • Speedster II brown wrap
  • Speedster II gold wrap
  • Speedster II chrome wrap
  • Speedster II color shift wrap
  • Speedster II carbon fiber wrap
  • Speedster II camo and patterned wrap

How much vinyl to wrap a PGO Speedster II

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2005–nowconvertible (2 doors)154.7 in (3,930 mm)about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m)

Speedster II wrap cost factors

Speedster II wrap cost depends on the film type, the finish and the amount of disassembly the installer needs to do. A full color change uses about 38 ft (11.5 m) of 60-inch (1.52 m) cast film, while chrome or patterned film uses about 48 ft (14.5 m). The convertible body means the top is not wrapped, which saves some labor, but the small size leaves tight curves on the rear deck and nose. A partial wrap or chrome delete on the window trim and badges costs less than a full wrap because it uses less film and fewer hours.

  • Film for a full wrap: about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Speedster II wraps by generation

Swipe sideways. Tap a card for the full description.

PGO Speedster II, first generation, factory photo
Factory color shown

2005–now Speedster II convertible (first generation)

2005–nowconvertible (2 doors)154.7 in (3,930 mm)

The first generation PGO Speedster II has a convertible top that is not wrapped during a color change. The film ends where the fabric top begins and is tucked under the rubber seal so the edge stays hidden. A folding hard top would be wrapped as panels of its own, but the Speedster II uses fabric only. This means the installer spends no time on the roof and the wrap can be finished faster than on a coupe.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 38 ft (11.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).

Roof, hood, chrome delete and PPF on a Speedster II

A partial wrap on the PGO Speedster II covers the hood, mirror caps and rear deck while the rest of the body keeps its original paint. Chrome delete on this car means covering the window trim and badges with black film for a monochrome look. Paint protection film (PPF) on the front end uses clear film to guard the nose, hood and mirror caps from stone chips. Each of these jobs uses less film than a full wrap and can be done without removing the doors or the fabric top.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a PGO Speedster II: body, cut-outs and film

A PGO Speedster II vinyl wrap follows the compact convertible body, which is 154.7 in (3,930 mm) long. The two-door body has a fabric top that is not wrapped, so the film ends where the top begins. The small size keeps material use low compared with larger sports cars. The curved rear deck and low nose require careful stretching and relief cuts for a smooth finish.

Speedster II wrap ideas start with removing the mirrors, door handles, badges and any bolt-on trim before film is applied. The fabric top is left uncovered, and the film edge is tucked under its seal for a clean line. Door jambs and the edges of the hood and rear deck are wrapped with the doors and lids open. The front bumper and rear bumper are wrapped on the car unless the owner asks for full edge coverage.

How much vinyl to wrap a Speedster II depends on the body, which has not changed since 2005. The same measurements apply to every year, so a full wrap always takes about 38 ft (11.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film uses about 48 ft (14.5 m) because the pattern must be matched at the seams. A partial wrap of the hood, mirror caps and rear deck uses less film and leaves the doors and fenders in factory paint.

Questions about wrapping a PGO Speedster II

How much vinyl does it take to wrap a PGO Speedster II?

It takes about 38 ft (11.5 m) of 60-inch (1.52 m) cast film to wrap a PGO Speedster II in a solid color. A chrome or patterned film needs about 48 ft (14.5 m) because the pattern must be aligned at the seams. The car is 154.7 in (3,930 mm) long, which keeps the material use low for a full wrap. The fabric top is not wrapped, so the film covers only the painted body panels.

Is the top of a Speedster II wrapped?

No, the fabric top of a Speedster II is not wrapped. The film ends where the top begins and is tucked under the rubber seal so the edge stays hidden. A folding hard top would be wrapped as panels of its own, but the Speedster II uses fabric only. The installer spends no time on the roof and the wrap can be finished faster than on a coupe.

Can I wrap only the hood or the roof of a Speedster II?

Yes, you can wrap only the hood, mirror caps and rear deck of a Speedster II as a partial wrap. A chrome delete on the window trim and badges is also an option if you want black accents without a full color change. Paint protection film (PPF) on the front end uses clear film to guard the nose, hood and mirror caps from stone chips. Each of these jobs uses less film than a full wrap and can be done without removing the doors or the fabric top.

Is a Speedster II hard to wrap?

A PGO Speedster II is not hard to wrap for an experienced installer, but the convertible body adds some work. The fabric top is not wrapped, and the film edge must be tucked under its seal for a clean line. The car is small at 154.7 in (3,930 mm), so the curved rear deck and low nose need careful stretching and relief cuts. The door jambs and bumper edges are wrapped with the panels open to hide the film edges.