Wraps by car

Alpine GTA wrap

The Alpine GTA wrap page covers the first generation of this rear-engined sports car, produced from 1985 to 1990. A full color change wrap on the coupe body takes about 46 ft (14 m) of 60-inch (1.52 m) cast vinyl wrap. If you choose a chrome or patterned film, plan for about 54 ft (16.5 m).

1generations14 mof film for a full wrap

Alpine GTA, first generation, factory photo
Alpine GTA, first generation. Factory color shown.

Alpine GTA wrap colors and ideas

  • Alpine GTA black wrap
  • Alpine GTA white wrap
  • Alpine GTA gray wrap
  • Alpine GTA silver wrap
  • Alpine GTA red wrap
  • Alpine GTA blue wrap
  • Alpine GTA green wrap
  • Alpine GTA yellow wrap
  • Alpine GTA orange wrap
  • Alpine GTA purple wrap
  • Alpine GTA pink wrap
  • Alpine GTA teal wrap
  • Alpine GTA brown wrap
  • Alpine GTA gold wrap
  • Alpine GTA chrome wrap
  • Alpine GTA color shift wrap
  • Alpine GTA carbon fiber wrap
  • Alpine GTA camo and patterned wrap

How much vinyl to wrap an Alpine GTA

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1985–1990coupe (2 doors)170.5 in (4,330 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m)

Alpine GTA wrap cost factors

The Alpine GTA wrap cost is affected by the amount of film: about 46 ft (14 m) of 60-inch (1.52 m) cast film. A chrome or patterned film needs about 54 ft (16.5 m), which adds material. Since the car has only two doors, labor focuses on large panels rather than many small areas.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Alpine GTA wraps by generation

Swipe sideways. Tap a card for the full description.

Alpine GTA, first generation, factory photo
Factory color shown

1985–1990 Alpine GTA coupe (first generation)

1985–1990coupe (2 doors)170.5 in (4,330 mm)

The first generation Alpine GTA was built from 1985 to 1990 as a two-door coupe. Paint age on these cars varies, so a test spot on a small area before the full wrap shows whether the film will adhere well. The car is 170.5 in (4,330 mm) long, and a full wrap takes about 46 ft (14 m) of 60-inch (1.52 m) cast film.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).

Roof, hood, chrome delete and PPF on an Alpine GTA

A partial wrap on the Alpine GTA can cover the roof, hood, or mirror caps without wrapping the whole car. An Alpine GTA chrome delete covers the window trim and badges with black film. You can also install paint protection film (PPF) on the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping an Alpine GTA: body, cut-outs and film

The Alpine GTA vinyl wrap covers a two-door coupe that is 170.5 in (4,330 mm) long, a size that suits a single installer working in stages. The car has two long side doors, and each door takes one large piece of film for a clean look. Because the body is compact, you use less film than on a modern four-door sedan.

Alpine GTA wrap ideas start with the two long side doors, which are large flat panels ideal for one-piece film application. The rear window and engine lid need careful cut-outs, and the side mirrors come off for a neat finish. You can also wrap the roof and hood as separate panels for a two-tone look.

How much vinyl to wrap an Alpine GTA depends on the film type: about 46 ft (14 m) of 60-inch (1.52 m) cast film for a standard color change. A chrome or patterned film needs about 54 ft (16.5 m) because of waste from pattern matching. All GTA bodies share the same shape, so the estimate holds for every year from 1985 to 1990.

Questions about wrapping an Alpine GTA

How much vinyl does it take to wrap an Alpine GTA?

It takes about 46 ft (14 m) of 60-inch (1.52 m) cast vinyl to wrap an Alpine GTA. For chrome or patterned film, allow about 54 ft (16.5 m) due to pattern matching waste.

Can I wrap only the hood or the roof of an Alpine GTA?

Yes, you can wrap only the hood or the roof of an Alpine GTA. Partial wrap options include the roof, hood, and mirror caps, and a chrome delete covers window trim and badges.

Is an Alpine GTA hard to wrap?

An Alpine GTA is not especially hard to wrap, but the two long side doors require large pieces of film that need careful handling. The car is 170.5 in (4,330 mm) long, so managing big panels without creases adds some work.

How many generations of the Alpine GTA does this page cover?

This page covers one generation of the Alpine GTA, the first generation produced from 1985 to 1990.