Wraps by car

BMW 321 wrap

This page covers the BMW 321, a mid-size car produced from 1937 to 1941 in one generation. A full wrap of the sedan body takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film. With chrome or patterned film, plan for about 64 ft (19.5 m) of vinyl wrap.

1generations16.5 mof film for a full wrap

BMW 321, first generation, factory photo
BMW 321, first generation. Factory color shown.

BMW 321 wrap colors and ideas

  • BMW 321 black wrap
  • BMW 321 white wrap
  • BMW 321 gray wrap
  • BMW 321 silver wrap
  • BMW 321 red wrap
  • BMW 321 blue wrap
  • BMW 321 green wrap
  • BMW 321 yellow wrap
  • BMW 321 orange wrap
  • BMW 321 purple wrap
  • BMW 321 pink wrap
  • BMW 321 teal wrap
  • BMW 321 brown wrap
  • BMW 321 gold wrap
  • BMW 321 chrome wrap
  • BMW 321 color shift wrap
  • BMW 321 carbon fiber wrap
  • BMW 321 camo and patterned wrap

How much vinyl to wrap a BMW 321

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1937–1941sedan (2 doors)177.2 in (4,500 mm)about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m)

BMW 321 wrap cost factors

BMW 321 wrap cost depends on the film you choose and the labor to prepare a car of these years. Plain cast film needs about 54 ft (16.5 m) of 60-inch (1.52 m) material, while chrome or patterned film needs about 64 ft (19.5 m). The two long side doors are large pieces, but the sedan shape has no complex wings or vents. Paint condition matters first: a test spot on an original or repainted panel shows whether the vinyl will bond cleanly.

  • Film for a full wrap: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).
  • Body: sedan (2 doors).
  • Two long side doors: each door is one large piece of film.

BMW 321 wraps by generation

Swipe sideways. Tap a card for the full description.

BMW 321, first generation, factory photo
Factory color shown

1937–1941 BMW 321 sedan (first generation)

1937–1941sedan (2 doors)177.2 in (4,500 mm)

The first generation BMW 321 was built from 1937 to 1941 as a two-door sedan with a length of 177.2 in (4,500 mm). Paint age is the main concern on a car of these years: panels may be original or repainted, and a test spot comes before a full wrap. Original paint can be too brittle for the film, while a fresh repaint needs time to cure. The installer checks the paint on every panel before ordering the full amount of vinyl.

Two long side doors: each door is one large piece of film.

Film: about 54 ft (16.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).

Roof, hood, chrome delete and PPF on a BMW 321

A partial wrap on a BMW 321 can cover the roof, the hood, or the mirror caps. Chrome delete on this car means covering the window trim and the badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips. Since the body has only two doors, the roof and the hood are small enough for a partial job.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a BMW 321: body, cut-outs and film

The BMW 321 vinyl wrap covers a two-door sedan body that is 177.2 in (4,500 mm) long. Two long side doors each take one large piece of film, which keeps panel seams to a minimum. The simple shape has no sharp creases, so a cast film can be worked into the corners without lifting. The roof and the curved rear section are the largest continuous areas to cover.

BMW 321 wrap ideas start with removing trim before the film goes on. Door handles, mirrors, lights, and the bumpers come off so the vinyl can be tucked around the edges. The grille and the hood ornament need cut-outs because they sit in the middle of the panels. The two long side doors need one large piece of film each, and any trim around the windows is removed first.

How much vinyl to wrap a BMW 321 depends only on the first generation body made from 1937 to 1941. The catalog lists one body style for this car, so the film estimate of about 54 ft (16.5 m) of 60-inch (1.52 m) cast film applies to every sedan. If you choose chrome or patterned film, order about 64 ft (19.5 m) to match the pattern at the seams. Since no other generation exists, installers do not adjust the yardage between years.

Questions about wrapping a BMW 321

How much vinyl does it take to wrap a BMW 321?

A BMW 321 wrap takes about 54 ft (16.5 m) of 60-inch (1.52 m) cast film for the whole sedan body. If you pick chrome or patterned film, the estimate is about 64 ft (19.5 m) because extra material is needed to align the pattern. These numbers cover the two-door body of the only generation, made from 1937 to 1941.

Can I wrap only the hood or the roof of a BMW 321?

Yes, you can wrap only the hood or the roof of a BMW 321. A partial wrap can also cover the mirror caps, or you can choose chrome delete on the window trim and badges. Paint protection film (PPF) is another partial option: clear film applied to the front end. These jobs use far less vinyl than a full wrap and leave the rest of the paint untouched.

Is a BMW 321 hard to wrap?

A BMW 321 is not hard to wrap for an installer who knows older paint. The body is a simple two-door sedan, but the two long side doors are each one large piece of film, so they need a second pair of hands to lay down smoothly. Paint age adds work: a test spot shows whether the surface can hold the vinyl. The size of 177.2 in (4,500 mm) means fewer panels, but each panel is bigger than on a modern car.

How many generations of the BMW 321 does this page cover?

This page covers one generation of the BMW 321, the first generation produced from 1937 to 1941. The catalog includes the sedan body with two doors and a length of 177.2 in (4,500 mm). No other generations are listed, so the wrap estimate is the same for every car on this page.