Wraps by car

BMW 501 wrap

The BMW 501 wrap page covers the first-generation sedan built from 1952 to 1958. A full vinyl wrap of this luxury car takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for about 67 ft (20.5 m). The page covers one generation in the catalog.

1generations17.5 mof film for a full wrap

BMW 501, first generation, factory photo
BMW 501, first generation. Factory color shown.

BMW 501 wrap colors and ideas

  • BMW 501 black wrap
  • BMW 501 white wrap
  • BMW 501 gray wrap
  • BMW 501 silver wrap
  • BMW 501 red wrap
  • BMW 501 blue wrap
  • BMW 501 green wrap
  • BMW 501 yellow wrap
  • BMW 501 orange wrap
  • BMW 501 purple wrap
  • BMW 501 pink wrap
  • BMW 501 teal wrap
  • BMW 501 brown wrap
  • BMW 501 gold wrap
  • BMW 501 chrome wrap
  • BMW 501 color shift wrap
  • BMW 501 carbon fiber wrap
  • BMW 501 camo and patterned wrap

How much vinyl to wrap a BMW 501

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1952–1958sedan (4 doors)186.2 in (4,730 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)

BMW 501 wrap cost factors

BMW 501 wrap cost depends on the size of the car, the film type, and the condition of the panels. At 186.2 in (4,730 mm), the sedan needs more film than a shorter modern car. Chrome or patterned film adds about 10 ft (3 m) to the material. The paint condition also matters, because old or repainted panels may need more preparation before the film is applied.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).
  • Body: sedan (4 doors).

BMW 501 wraps by generation

Swipe sideways. Tap a card for the full description.

BMW 501, first generation, factory photo
Factory color shown

1952–1958 BMW 501 sedan (first generation)

1952–1958sedan (4 doors)186.2 in (4,730 mm)

Paint age on a car of these years is the first thing to check before wrapping a BMW 501. Panels may be original or repainted, and old paint can lift when the film is removed. A test spot on a small area shows whether the paint will hold. Do this before ordering the full amount of film.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Roof, hood, chrome delete and PPF on a BMW 501

A partial wrap on a BMW 501 works well for the roof, hood, or mirror caps. Chrome delete covers the window trim and badges with black film. Paint protection film (PPF) can be applied as clear film on the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a BMW 501: body, cut-outs and film

BMW 501 vinyl wrap work starts with a four-door sedan that is 186.2 in (4,730 mm) long. The long, flat roof and tall doors are straightforward to cover with a single person on each side. The body has few sharp creases, so the film can follow the original lines without much stretching. The large panels mean you will use more material than on a small modern coupe.

BMW 501 wrap ideas should account for the bright trim around the windows and the large chrome grille. The door handles, badges, and trim need careful cut-outs or removal before the film goes on. The front grille comes off separately, which gives you a clean edge behind it. The bumpers are also removed for a neat wrap at the front and rear.

Knowing how much vinyl to wrap a BMW 501 depends on the generation, but this page covers only the 1952–1958 sedan. All cars of this generation share the same body length and panel shapes. A wrapper who counts film for this car will not need to adjust between early and late production years.

Questions about wrapping a BMW 501

How much vinyl does it take to wrap a BMW 501?

About 57 ft (17.5 m) of 60-inch (1.52 m) cast film. The BMW 501 is a large sedan that needs a generous amount of vinyl. If you use chrome or patterned film, the estimate rises to about 67 ft (20.5 m).

Can I wrap only the hood or the roof of a BMW 501?

Yes, you can wrap only the hood or the roof of a BMW 501. A partial wrap is a smaller job that also includes the mirror caps. Chrome delete is another option for the window trim and badges.

Is a BMW 501 hard to wrap?

The BMW 501 is not the easiest car to wrap because of its size and chrome details. The long body calls for careful handling of large film sheets. The bright window trim, grille, and badges all need cut-outs or removal, which adds work.

How many generations of the BMW 501 does this page cover?

One generation. The BMW 501 on this page is the first generation, produced from 1952 to 1958.