Wraps by car

BMW 507 wrap

A BMW 507 wrap covers the first generation of this classic roadster, built from 1956 to 1959. This single-generation convertible body is 172.4 in (4,380 mm) long. A full vinyl wrap of the BMW 507 uses about 39 ft (12 m) of 60-inch (1.52 m) cast film.

1generations12 mof film for a full wrap

BMW 507, first generation, factory photo
BMW 507, first generation. Factory color shown.

BMW 507 wrap colors and ideas

  • BMW 507 black wrap
  • BMW 507 white wrap
  • BMW 507 gray wrap
  • BMW 507 silver wrap
  • BMW 507 red wrap
  • BMW 507 blue wrap
  • BMW 507 green wrap
  • BMW 507 yellow wrap
  • BMW 507 orange wrap
  • BMW 507 purple wrap
  • BMW 507 pink wrap
  • BMW 507 teal wrap
  • BMW 507 brown wrap
  • BMW 507 gold wrap
  • BMW 507 chrome wrap
  • BMW 507 color shift wrap
  • BMW 507 carbon fiber wrap
  • BMW 507 camo and patterned wrap

How much vinyl to wrap a BMW 507

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1956–1959convertible (2 doors)172.4 in (4,380 mm)about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

BMW 507 wrap cost factors

BMW 507 wrap cost depends on the film, the condition of the 1956–1959 body, and how much trim is removed. The car's 172.4 in (4,380 mm) length and curved panels add labor compared with flat modern bodies. A full wrap uses about 39 ft (12 m) of 60-inch (1.52 m) cast film, while chrome or patterned film needs about 51 ft (15.5 m). Surface preparation on an older car can also raise the total work.

  • Film for a full wrap: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

BMW 507 wraps by generation

Swipe sideways. Tap a card for the full description.

BMW 507, first generation, factory photo
Factory color shown

1956–1959 BMW 507 convertible (first generation)

1956–1959convertible (2 doors)172.4 in (4,380 mm)

The first generation BMW 507 has an open top that is not wrapped. The fabric top folds away and the vinyl wrap ends where the top boot meets the rear body. If the car has a folding hard top, that panel is wrapped separately from the main body. The film follows the door and hood edges so the soft top can still operate freely.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a BMW 507

A BMW 507 chrome delete covers the window trim and badges with black film. Partial wrap jobs on this car often include the hood, mirror caps, or rear deck. Paint protection film (PPF) on the front end uses clear film to guard the nose and front fenders. These smaller jobs leave the rest of the classic body in its original paint.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a BMW 507: body, cut-outs and film

A BMW 507 vinyl wrap follows the lines of a compact two-door convertible. The body has no fixed roof, so film covers the hood, doors, fenders, and rear deck as separate panels. The 172.4 in (4,380 mm) length means a single roll of 60-inch (1.52 m) film can span most panels without seams. Installers plan the wrap around the door cut lines and the curved rear fenders.

BMW 507 wrap ideas start with the chrome trim and the open cockpit. The door handles, grille surround, and side spears can be removed or wrapped carefully for a clean edge. The fabric top is not wrapped, and film ends where the top mechanism meets the body. A folding hard top would be wrapped as its own panels, but the standard soft top stays uncovered.

How much vinyl to wrap a BMW 507 depends on the film type and the areas chosen. A full color change with cast film takes about 39 ft (12 m) of 60-inch (1.52 m) material. Chrome or patterned film for the same body needs about 51 ft (15.5 m) because it has more waste around curves. The first generation is the only body style for the 507, so there are no other sizes to compare.

Questions about wrapping a BMW 507

How much vinyl does it take to wrap a BMW 507?

It takes about 39 ft (12 m) of 60-inch (1.52 m) cast vinyl wrap to cover a BMW 507 fully. That figure is for a standard color change wrap on the first generation body. Chrome or patterned film requires about 51 ft (15.5 m) because of extra waste from the curves and chrome details.

Is the top of a BMW 507 wrapped?

No, the fabric top of a BMW 507 is not wrapped. The vinyl film ends where the soft top meets the body at the rear deck and side windows. A folding hard top, if present, would be wrapped as separate panels. The convertible top itself stays uncovered to fold and operate normally.

Can I wrap only the hood or the roof of a BMW 507?

Yes, you can wrap only the hood or the rear deck of a BMW 507. A partial wrap on this car often covers the hood, mirror caps, or rear deck. The roof is not a wrap panel because this is a convertible with a fabric top. These smaller jobs let you change one section without a full car wrap.

Is a BMW 507 hard to wrap?

Yes, a BMW 507 is harder to wrap than a modern sedan. The 1956–1959 body is 172.4 in (4,380 mm) long with many curved surfaces and chrome details. The convertible top adds work because the film must end cleanly where the soft top meets the body. Installers often remove or mask the door handles, grille, and side spears for a neat edge.