Wraps by car

BMW E3 wrap

The BMW E3 wrap page covers the first generation luxury sedan built from 1968 to 1977. A full vinyl wrap of this four-door body takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film raises the estimate to about 67 ft (20.5 m).

1generations17.5 mof film for a full wrap

BMW E3, first generation, factory photo
BMW E3, first generation. Factory color shown.

BMW E3 wrap colors and ideas

  • BMW E3 black wrap
  • BMW E3 white wrap
  • BMW E3 gray wrap
  • BMW E3 silver wrap
  • BMW E3 red wrap
  • BMW E3 blue wrap
  • BMW E3 green wrap
  • BMW E3 yellow wrap
  • BMW E3 orange wrap
  • BMW E3 purple wrap
  • BMW E3 pink wrap
  • BMW E3 teal wrap
  • BMW E3 brown wrap
  • BMW E3 gold wrap
  • BMW E3 chrome wrap
  • BMW E3 color shift wrap
  • BMW E3 carbon fiber wrap
  • BMW E3 camo and patterned wrap

How much vinyl to wrap a BMW E3

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1968–1977sedan (4 doors)185.0 in (4,700 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)

BMW E3 wrap cost factors

BMW E3 wrap cost depends on the size of the sedan, which needs about 57 ft (17.5 m) of film for a full color change. A chrome or patterned film job uses about 67 ft (20.5 m) and more labor for trimming. The paint condition on a 1968 to 1977 car also changes the preparation. A partial wrap or chrome delete needs less material and less time.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).
  • Body: sedan (4 doors).

BMW E3 wraps by generation

Swipe sideways. Tap a card for the full description.

BMW E3, first generation, factory photo
Factory color shown

1968–1977 BMW E3 sedan (first generation)

1968–1977sedan (4 doors)185.0 in (4,700 mm)

The first generation BMW E3 was produced from 1968 to 1977 as a four-door luxury sedan. On a car of these years the paint may be original or repainted, so a test spot comes before a full wrap. Old paint can lift when film is removed, and a test spot shows whether the surface is stable. The panels are steel, and rust repair has to be finished before wrapping.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Roof, hood, chrome delete and PPF on a BMW E3

A partial wrap on a BMW E3 covers the roof, hood, or mirror caps with the same cast film used for a full wrap. A chrome delete turns the window trim and badges black with a narrower film. Paint protection film (PPF) is a clear film that goes on the front end to guard against stone chips. Any of these jobs changes the look of the sedan without wrapping the whole body.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a BMW E3: body, cut-outs and film

A BMW E3 vinyl wrap deals with one body style, a four-door sedan with a length of 185.0 in (4,700 mm). The long roof and tall rear pillars add surface area on the upper body. The doors are large, so each panel needs careful positioning. The trunk lid and hood are broad and flat, which helps the film lay down smoothly.

BMW E3 wrap ideas start with the chrome beltline trim that runs along the shoulders. Window surrounds, door handles, and the front grille need cut-outs or removal for a clean edge. The bumpers are chrome and usually come off for a color change wrap. Badging on the trunk and front fenders is removed before film goes over the panel.

How much vinyl to wrap a BMW E3 depends on the single generation made from 1968 to 1977. There are no later bodies to compare, so the film estimate stays the same for every year. A car with a vinyl roof needs less film on that panel because the roof is already covered. The catalog counts one generation for this model.

Questions about wrapping a BMW E3

How much vinyl does it take to wrap a BMW E3?

A full BMW E3 wrap takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. With chrome or patterned film the estimate is about 67 ft (20.5 m). The four-door sedan has a length of 185.0 in (4,700 mm), which drives the amount of material. A partial job uses less film than these figures.

Can I wrap only the hood or the roof of a BMW E3?

Yes, you can wrap only the hood or the roof of a BMW E3. A partial wrap on this car covers the roof, hood, or mirror caps with the same cast film used for a full wrap. The hood is a single flat panel that is straightforward to cover. The roof has a vinyl roof option on some cars, which changes how the film adheres.

Is a BMW E3 hard to wrap?

A BMW E3 is not the easiest sedan to wrap because of its chrome trim and old paint. The chrome beltline trim, window surrounds, and bumpers need removal or cut-outs, which adds labor. The body is long at 185.0 in (4,700 mm), so large panels need careful handling. Paint from 1968 to 1977 may be fragile, so a test spot is needed before a full wrap.

How many generations of the BMW E3 does this page cover?

This page covers one generation of the BMW E3. The first generation was produced from 1968 to 1977 as a four-door luxury sedan. The catalog counts a single generation for this model. All years of the E3 share the same body style and film estimate.