Wraps by car

Brabus SV12 wrap

The Brabus SV12 wrap page covers the first generation sedan produced from 2009 to 2013. A full vinyl wrap on this luxury car uses about 62 ft (19 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, the estimate rises to about 70 ft (21.5 m).

1generations19 mof film for a full wrap

Brabus SV12, first generation, factory photo
Brabus SV12, first generation. Factory color shown.

Brabus SV12 wrap colors and ideas

  • Brabus SV12 black wrap
  • Brabus SV12 white wrap
  • Brabus SV12 gray wrap
  • Brabus SV12 silver wrap
  • Brabus SV12 red wrap
  • Brabus SV12 blue wrap
  • Brabus SV12 green wrap
  • Brabus SV12 yellow wrap
  • Brabus SV12 orange wrap
  • Brabus SV12 purple wrap
  • Brabus SV12 pink wrap
  • Brabus SV12 teal wrap
  • Brabus SV12 brown wrap
  • Brabus SV12 gold wrap
  • Brabus SV12 chrome wrap
  • Brabus SV12 color shift wrap
  • Brabus SV12 carbon fiber wrap
  • Brabus SV12 camo and patterned wrap

How much vinyl to wrap a Brabus SV12

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2009–2013sedan (4 doors)205.7 in (5,226 mm)about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m)

Brabus SV12 wrap cost factors

Brabus SV12 wrap cost depends on the size of the sedan at 205.7 in (5,226 mm) and the type of film chosen. Full coverage with cast film requires about 62 ft (19 m), while chrome or patterned film needs about 70 ft (21.5 m). Additional bodywork preparation, such as paint correction, can also affect the final cost.

  • Film for a full wrap: about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).
  • Body: sedan (4 doors).

Brabus SV12 wraps by generation

Swipe sideways. Tap a card for the full description.

Brabus SV12, first generation, factory photo
Factory color shown

2009–2013 Brabus SV12 sedan (first generation)

2009–2013sedan (4 doors)205.7 in (5,226 mm)

The first generation Brabus SV12 spans 2009–2013 and may have original or repainted panels due to paint age. A test spot is recommended before a full wrap to check paint adhesion. Installers should inspect each panel for clear coat failure before applying film.

Film: about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).

Roof, hood, chrome delete and PPF on a Brabus SV12

A partial wrap on the Brabus SV12 includes the roof, hood, or mirror caps. Chrome delete covers the window trim and badges with black film. Paint protection film (PPF) can be applied as clear film on the front end.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Brabus SV12: body, cut-outs and film

A Brabus SV12 vinyl wrap must address the sedan body with four doors and a length of 205.7 in (5,226 mm). The large panels and long roofline require careful planning for film coverage. Experienced installers account for the extra material needed for bumpers and side skirts.

For Brabus SV12 wrap ideas, consider leaving mirrors and trim wrapped but removing door handles for a cleaner finish. Emblems and badges need precise cut-outs or are removed and reapplied after wrapping. The front bumper intakes and side vents require relief cuts for proper adhesion.

When figuring how much vinyl to wrap a Brabus SV12, this first generation has only one body style, so the film estimate is consistent. The 2009–2013 sedan does not vary in size across trim levels. You can rely on the listed amount as a starting point for ordering film.

Questions about wrapping a Brabus SV12

How much vinyl does it take to wrap a Brabus SV12?

It takes about 62 ft (19 m) of 60-inch (1.52 m) cast film to wrap a Brabus SV12, or about 70 ft (21.5 m) for chrome or patterned film. These figures come from the film estimate for the newest body.

Can I wrap only the hood or the roof of a Brabus SV12?

Yes, you can wrap only the hood or the roof of a Brabus SV12. Partial wrap options include the roof, hood, and mirror caps.

Is a Brabus SV12 hard to wrap?

Yes, a Brabus SV12 is hard to wrap because of its size at 205.7 in (5,226 mm) and the need for relief cuts on bumpers. Door handles and emblems require removal or precise cutting, adding labor time.

How many generations of the Brabus SV12 does this page cover?

This page covers one generation of the Brabus SV12, the first generation produced from 2009 to 2013.