Wraps by car

Volkswagen Taro wrap

The Volkswagen Taro wrap page covers the first generation pickup produced from 1989 to 1997. One generation is in the catalog. A full wrap of the newest body takes about 56 ft (17 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, plan on about 66 ft (20 m) of vinyl wrap.

1generations17 mof film for a full wrap

Volkswagen Taro, first generation, factory photo
Volkswagen Taro, first generation. Factory color shown.

Volkswagen Taro wrap colors and ideas

  • Taro black wrap
  • Taro white wrap
  • Taro gray wrap
  • Taro silver wrap
  • Taro red wrap
  • Taro blue wrap
  • Taro green wrap
  • Taro yellow wrap
  • Taro orange wrap
  • Taro purple wrap
  • Taro pink wrap
  • Taro teal wrap
  • Taro brown wrap
  • Taro gold wrap
  • Taro chrome wrap
  • Taro color shift wrap
  • Taro carbon fiber wrap
  • Taro camo and patterned wrap

How much vinyl to wrap a Volkswagen Taro

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1989–1997pickup (2 or 4 doors)186.0 in (4,725 mm)about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m)

Taro wrap cost factors

Taro wrap cost depends on the size of the vehicle and the film type. The pickup is 186.0 in (4,725 mm) long, and a full wrap uses about 56 ft (17 m) of cast film. Chrome or patterned film raises the material amount to about 66 ft (20 m). The two-body design of cab and bed also adds labor, as each section is wrapped separately.

  • Film for a full wrap: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).
  • Body: pickup (2 or 4 doors).
  • A pickup bed: the cab and the bed are wrapped as two bodies, and the inside of the bed is not wrapped.

Taro wraps by generation

Swipe sideways. Tap a card for the full description.

Volkswagen Taro, first generation, factory photo
Factory color shown

1989–1997 Taro pickup (first generation)

1989–1997pickup (2 or 4 doors)186.0 in (4,725 mm)

The first generation Volkswagen Taro, built from 1989 to 1997, is a pickup with 2 or 4 doors. It is 186.0 in (4,725 mm) long, so a wrap needs about 56 ft (17 m) of film. The pickup bed means the cab and the bed are wrapped as two bodies. The inside of the bed is not wrapped, leaving that area bare.

A pickup bed: the cab and the bed are wrapped as two bodies, and the inside of the bed is not wrapped.

Film: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).

Roof, hood, chrome delete and PPF on a Taro

A partial wrap on a Taro can cover the roof, hood, or mirror caps. Taro chrome delete changes the window trim and badges to black film. Paint protection film (PPF) on the front end uses clear film to guard the hood and bumper. These jobs use less film than a full wrap and focus on specific areas.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Volkswagen Taro: body, cut-outs and film

The Volkswagen Taro vinyl wrap must handle a pickup body that is 186.0 in (4,725 mm) long. The cab and the bed are wrapped as two separate bodies, so the film is cut and installed in pieces. The inside of the bed is not wrapped, which keeps the job simpler than a full van wrap.

Taro wrap ideas start with the pickup bed: the cab and the bed are two bodies for the film. The inside of the bed stays bare, so no film is needed there. The door handles, mirrors, and badges may need cut-outs or removal during the wrap. This setup lets you use a different color or finish on the bed than on the cab.

When counting how much vinyl to wrap a Taro, note that only one generation is listed from 1989 to 1997. There are no other generations to compare, so the film estimate stays the same for all years. The body style is a pickup with 2 or 4 doors, and both versions are the same length. This means the film amount does not change between models.

Questions about wrapping a Volkswagen Taro

How much vinyl does it take to wrap a Volkswagen Taro?

Yes, a full wrap of a Volkswagen Taro takes about 56 ft (17 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, the amount is about 66 ft (20 m). This estimate covers the whole pickup body, both cab and bed. The inside of the bed is not wrapped, so no extra film is needed there.

Is the bed of a Taro wrapped?

No, the inside of the bed of a Taro is not wrapped. The cab and the bed are wrapped as two separate bodies, but only the outside surfaces get film. The bed walls and floor stay bare. This keeps the wrap from being damaged by cargo.

Can I wrap only the hood or the roof of a Taro?

Yes, you can wrap only the hood or the roof of a Taro. The partial wrap option covers the roof, hood, or mirror caps. These smaller jobs use less film and leave the rest of the pickup untouched.

Is a Taro hard to wrap?

A Taro is not very hard to wrap, but the pickup bed adds work. The cab and the bed are two separate bodies, so the installer must wrap each section individually. The inside of the bed is not wrapped, which saves time. The length of 186.0 in (4,725 mm) means long panels on the bed sides.