A partial vehicle wrap covers only some panels, such as the hood, roof, sides or rear. The paint shows on the rest of the body and becomes part of the design. On a work vehicle, the wrapped panels carry the graphics while the paint carries the base color.

Key facts

  • A partial wrap uses the paint color as part of the finished design.
  • The film calculator puts a pickup roof at 3.5 m (11 ft) of cast film.
  • A van roof takes 10.5 m (34 ft) of cast film, the largest roof figure in the calculator.
  • Film laid next to paint must be checked against that paint on a real sample.

What is a partial vehicle wrap

A partial vehicle wrap covers selected panels and leaves the rest of the paint on show. The film can be a plain color, a finish such as carbon, or printed graphics. Film edges are placed on body lines so the change looks planned.

A partial wrap is also called a half wrap when it covers about half the body. A quarter wrap or spot graphics cover less, such as the rear doors or tailgate.

Partial vehicle wrap graphics for a work vehicle

Partial vehicle wrap graphics put the business message where people look: sides, rear and tailgate. The paint, often white or another plain color, works as the background. A large shape or color sweep can run from the rear forward across part of each side.

Plan the graphics around the paint color, since it fills every part left uncovered. Fleet planning across many vehicles is covered in the guide to commercial and fleet wraps.

  • Rear doors or tailgate with name, service and contact details.
  • A color sweep along the lower sides, with the upper paint left plain.
  • Door panels with logo and lettering.
  • A wrapped hood or roof in the brand color.

Partial truck wrap: panels and film amounts

A partial truck wrap can cover the hood, the roof, the tailgate or the lower sides. Each panel can be planned on its own, so the job can grow later. The film calculator on this site gives roof and hood amounts by body type.

The table shows cast film for one panel, rounded up to 0.5 m. Figures include spare for one re-cut, but they are estimates and not a cutting plan.

Body typeRoofHood
Pickup3.5 m (11 ft)3 m (10 ft)
Van10.5 m (34 ft)2.5 m (8 ft)
Minivan6 m (20 ft)2 m (7 ft)
SUV4.5 m (15 ft)2.5 m (8 ft)
Off-roader4.5 m (15 ft)2.5 m (8 ft)
Sedan3.5 m (11 ft)3 m (10 ft)

Can you do a partial wrap on a car

Yes, a partial wrap works on a car as well as on a truck or van. A gloss black roof, a carbon hood and a chrome delete are three examples. A chrome delete means covering bright trim with black film.

Creative ideas for partial car wraps play with contrast between film and paint. A matte stripe over gloss paint, or a satin hood on a metallic car, reads clearly. The catalog on this site holds 106 carbon fiber and 42 forged carbon films for such panels.

Matching film to the paint beside it

Film next to paint is judged by eye, so the match matters more than on a full wrap. Even a film named like the paint color can differ in tone or sheen. Hold a real sample on the panel in daylight before you order.

Contrast avoids the problem altogether, because nobody expects two different finishes to match. Black, carbon and matte films give a clear contrast on roofs, hoods and mirrors.

What a partial wrap cost depends on

The cost of a partial wrap depends on the panels covered and the film chosen. Chrome and printed films add time compared with plain color film. Complex shapes, such as bumpers and mirrors, take longer than a flat hood or roof.

Prep work matters too, because film shows any chip or dent in the paint beneath. Ask the installer to check the paint on each panel before quoting.

Questions

What is a partial vehicle wrap?

A partial vehicle wrap covers some panels of a vehicle and leaves the rest painted. The paint becomes the background for the wrapped areas and any graphics. Hood, roof, tailgate, doors and lower sides are panels it can cover.

How much does a partial truck wrap cost?

A partial truck wrap cost depends on the panels, the film and the design work. A roof or hood alone takes far less film than a full wrap, as the table shows. Printed graphics add artwork and print time on top of the film and fitting.

Can you do a partial wrap on a car?

Yes, any panel that film can cover can be wrapped on its own. Roofs, hoods, mirrors and trim are panels wrapped on cars this way. Check that the film suits the paint next to it before ordering.

What are some creative ideas for partial car wraps?

A contrasting roof, a carbon hood and a color sweep along the sides are three ideas. A chrome delete in gloss or satin black changes the look of the trim. The visualizer on this site shows patterned looks such as camouflage, honeycomb and brushed metal.

Is it better to wrap or paint part of a truck?

Wrap part of a truck when you want graphics or a finish you may change later. Paint suits a permanent repair or one color matched to the factory finish. The guide to commercial and fleet wraps weighs wrap against paint in more detail.

Films from this guide