Wraps by car

Austin Metro wrap

The Austin Metro wrap page covers the first generation, built from 1980 to 1990. This subcompact hatchback was offered with three or five doors. A full vinyl wrap of the newest body takes about 39 ft (12 m) of 60-inch (1.52 m) cast film.

1generations12 mof film for a full wrap

Austin Metro, first generation, factory photo
Austin Metro, first generation. Factory color shown.

Austin Metro wrap colors and ideas

  • Metro black wrap
  • Metro white wrap
  • Metro gray wrap
  • Metro silver wrap
  • Metro red wrap
  • Metro blue wrap
  • Metro green wrap
  • Metro yellow wrap
  • Metro orange wrap
  • Metro purple wrap
  • Metro pink wrap
  • Metro teal wrap
  • Metro brown wrap
  • Metro gold wrap
  • Metro chrome wrap
  • Metro color shift wrap
  • Metro carbon fiber wrap
  • Metro camo and patterned wrap

How much vinyl to wrap an Austin Metro

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1980–1990hatchback (3 or 5 doors)134.1 in (3,405 mm) to 142.9 in (3,630 mm)about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

Metro wrap cost factors

Metro wrap cost depends on the film width, the area of the panels, and the number of cut-outs. The hatchback body has a large tailgate and short overhangs, which keeps waste low. The 134.1 in (3,405 mm) to 142.9 in (3,630 mm) length changes how much film a shop lays out.

  • Film for a full wrap: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: hatchback (3 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Metro wraps by generation

Swipe sideways. Tap a card for the full description.

Austin Metro, first generation, factory photo
Factory color shown

1980–1990 Metro hatchback (first generation)

1980–1990hatchback (3 or 5 doors)134.1 in (3,405 mm) to 142.9 in (3,630 mm)

The first generation Metro has paint that is now over three decades old, and panels may be original or repainted. A wrap shop tests a small spot before a full wrap to check adhesion on old paint. If the paint is chalky or peeling, it must be corrected before film goes on.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 39 ft (12 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Metro

A partial wrap on a Metro can cover the roof, hood, or mirror caps without wrapping the whole car. Metro chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Austin Metro: body, cut-outs and film

The Austin Metro vinyl wrap fits a car between 134.1 in (3,405 mm) and 142.9 in (3,630 mm) long. Its small size keeps the wrap area modest compared with modern subcompacts. The hatchback shape means one large tailgate and two roof sections on the five-door.

Metro wrap ideas start with the tailgate, where the film ends at the edge of the rear glass. The tailgate glass is set into the panel, so no cut-out is needed on the metal. Installers remove badges and door handles before laying film over those areas.

How much vinyl to wrap a Metro depends on the body length of the car you own. The earlier cars are shorter and use slightly less film than the later ones. For planning, measure both sides, the roof, and the tailgate before ordering material.

Questions about wrapping an Austin Metro

How much vinyl does it take to wrap an Austin Metro?

About 39 ft (12 m) of 60-inch (1.52 m) cast film is enough to wrap the newest Austin Metro body. The estimate is for a full color change wrap on the largest version of the car. If you add patterned or chrome film, allow about 51 ft (15.5 m).

Can I wrap only the hood or the roof of a Metro?

Yes, you can wrap only the hood or the roof of a Metro. Those panels are included in the partial wrap options for this car. A shop can also cover just the mirror caps or do a chrome delete on the window trim and badges.

Is a Metro hard to wrap?

A Metro adds work because the tailgate glass sits in the panel and the film ends at its edge. The car is small, so the total area is easy to manage on a single roll of 60-inch (1.52 m) film. The old paint on a first generation car also needs a test spot for adhesion.

How many generations of the Metro does this page cover?

This page covers one generation of the Metro, built from 1980 to 1990. It was the only generation before the car was replaced by the Rover Metro. All body styles in those years share the same wrap estimate.