Wraps by car

De Tomaso Bigua wrap

The De Tomaso Bigua wrap page covers the single first generation built from 2000 to 2002. This page includes the car in full, its one generation and the film a full wrap of the newest body takes. A full vinyl wrap of the Bigua needs about 44 ft (13.5 m) of 60-inch (1.52 m) cast film.

1generations13.5 mof film for a full wrap

De Tomaso Bigua, first generation, factory photo
De Tomaso Bigua, first generation. Factory color shown.

De Tomaso Bigua wrap colors and ideas

  • Bigua black wrap
  • Bigua white wrap
  • Bigua gray wrap
  • Bigua silver wrap
  • Bigua red wrap
  • Bigua blue wrap
  • Bigua green wrap
  • Bigua yellow wrap
  • Bigua orange wrap
  • Bigua purple wrap
  • Bigua pink wrap
  • Bigua teal wrap
  • Bigua brown wrap
  • Bigua gold wrap
  • Bigua chrome wrap
  • Bigua color shift wrap
  • Bigua carbon fiber wrap
  • Bigua camo and patterned wrap

How much vinyl to wrap a De Tomaso Bigua

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2000–2002convertible (2 doors)165.1 in (4,194 mm)about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

Bigua wrap cost factors

Bigua wrap cost depends on the film type, the condition of the paint and the shop's labor rate for a rare sports car. The small body of 165.1 in (4,194 mm) uses less film than a large sedan, but the convertible edges and curved rear deck add installation time. A chrome or patterned film raises the cost because it needs about 51 ft (15.5 m) of material. Paint protection film (PPF) work also adds cost because it must be cut and wrapped around the front end.

  • Film for a full wrap: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Bigua wraps by generation

Swipe sideways. Tap a card for the full description.

De Tomaso Bigua, first generation, factory photo
Factory color shown

2000–2002 Bigua convertible (first generation)

2000–2002convertible (2 doors)165.1 in (4,194 mm)

The first generation Bigua is a convertible and its open top is not wrapped. A fabric top is left as it is and the film ends cleanly where the top begins. If the car has a folding hard top, that top is wrapped as separate panels of its own. The installer must plan the cut lines around the top opening to avoid lifting edges.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 44 ft (13.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Bigua

A partial wrap on the Bigua can cover the hood, mirror caps and rear deck. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is clear film on the front end to shield the paint from chips. These partial jobs use less film than a full wrap and cost less in labor.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a De Tomaso Bigua: body, cut-outs and film

The De Tomaso Bigua vinyl wrap is shaped by its convertible sports car body and compact 165.1 in (4,194 mm) length. A convertible body means the fabric top is not wrapped and the film ends where it begins. The short two-door body keeps panel sizes small, but the open top area adds extra edges to finish cleanly. With one generation only, there is no variation in body styles to plan around.

Bigua wrap ideas start with the parts that need cut-outs or come off. The convertible body has a fabric top that is not wrapped and the film ends where it begins; a folding hard top would be wrapped as panels of its own. The side mirrors, door handles and badges should be removed or cut around for a clean install. The short overhangs and curved rear deck need relief cuts to avoid overstretching the film.

How much vinyl to wrap a Bigua depends on the generation you own. The only generation, from 2000 to 2002, has one body style: a convertible with 2 doors. The length stays 165.1 in (4,194 mm), so the film estimate does not change. You need about 44 ft (13.5 m) of 60-inch (1.52 m) cast film for the whole body.

Questions about wrapping a De Tomaso Bigua

How much vinyl does it take to wrap a De Tomaso Bigua?

A De Tomaso Bigua takes about 44 ft (13.5 m) of 60-inch (1.52 m) cast film for a full wrap. This figure comes from the film estimate of the newest body in the catalog. If you choose chrome or patterned film, add about 7 ft (2 m) more.

Is the top of a Bigua wrapped?

No, the top of a Bigua is not wrapped when it is a fabric convertible top. The film ends where the top begins because wrapping fabric is not possible with a vinyl wrap. If the car has a folding hard top, that top is wrapped as panels of its own.

Can I wrap only the hood or the roof of a Bigua?

Yes, you can wrap only the hood or the rear deck of a Bigua. A partial wrap on the Bigua can cover the hood, mirror caps and rear deck. A roof is not available in the same way because the car is a convertible without a fixed roof.

Is a Bigua hard to wrap?

Yes, a Bigua is harder to wrap than a typical sedan because of its convertible body and small curves. The fabric top is not wrapped and the film ends where it begins, which demands careful cutting. The short length of 165.1 in (4,194 mm) means tight panels and the rear deck has a pronounced curve that can cause wrinkles. The installer must remove or cut around small parts like mirror caps and badges.