Wraps by car

Haima 7 wrap

The Haima 7 wrap page covers the first generation SUV produced from 2013 to 2016. A full vinyl wrap of the body needs about 59 ft (18 m) of 60-inch (1.52 m) cast film. With chrome or patterned film, plan for about 69 ft (21 m) to allow pattern matching.

1generations18 mof film for a full wrap

Haima 7, first generation, factory photo
Haima 7, first generation. Factory color shown.

Haima 7 wrap colors and ideas

  • Haima 7 black wrap
  • Haima 7 white wrap
  • Haima 7 gray wrap
  • Haima 7 silver wrap
  • Haima 7 red wrap
  • Haima 7 blue wrap
  • Haima 7 green wrap
  • Haima 7 yellow wrap
  • Haima 7 orange wrap
  • Haima 7 purple wrap
  • Haima 7 pink wrap
  • Haima 7 teal wrap
  • Haima 7 brown wrap
  • Haima 7 gold wrap
  • Haima 7 chrome wrap
  • Haima 7 color shift wrap
  • Haima 7 carbon fiber wrap
  • Haima 7 camo and patterned wrap

How much vinyl to wrap a Haima 7

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2013–2016SUV (5 doors)174.8 in (4,441 mm)about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)

Haima 7 wrap cost factors

The Haima 7 wrap cost depends on the size and finish of the film, not on a listed rate. A full wrap of this 174.8 in (4,441 mm) SUV uses about 59 ft (18 m) of cast film, or about 69 ft (21 m) for chrome or patterned film. The cost also changes with the amount of trim removal, such as taking off the roof rails.

  • Film for a full wrap: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: SUV (5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Every trim has roof rails: they come off before the roof is wrapped, or the film is cut along them.
  • Every trim has parking sensors in the bumpers: the film is cut around each sensor.

Haima 7 wraps by generation

Swipe sideways. Tap a card for the full description.

Haima 7, first generation, factory photo
Factory color shown

2013–2016 Haima 7 SUV (first generation)

2013–2016SUV (5 doors)174.8 in (4,441 mm)

The first generation Haima 7 was produced from 2013 to 2016 as a five-door SUV. It is 174.8 in (4,441 mm) long and is the only generation of this model. The roof rails come off before the roof is wrapped, or the film is cut along them.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Every trim has roof rails: they come off before the roof is wrapped, or the film is cut along them.

Every trim has parking sensors in the bumpers: the film is cut around each sensor.

Film: about 59 ft (18 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Roof, hood, chrome delete and PPF on a Haima 7

A partial wrap on a Haima 7 can cover the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Haima 7: body, cut-outs and film

The Haima 7 vinyl wrap covers a five-door SUV that is 174.8 in (4,441 mm) long. The tall roof and large side panels make the wrap straightforward for a shop with experience on SUVs. Because the tailgate glass is set into the rear door, the film ends at the glass edge instead of wrapping around it.

Haima 7 wrap ideas often start with cutting the film around each parking sensor in the bumpers. The tailgate glass is left uncovered, so the vinyl is trimmed to its edge. Roof rails on every trim can be removed before wrapping the roof or the film is cut along them.

To work out how much vinyl to wrap a Haima 7, use the measurements of the first generation as your guide. A color change wrap of the full body uses about 59 ft (18 m) of 60-inch film. Chrome or patterned vinyl needs about 69 ft (21 m), because the pattern must be matched at the seams.

Questions about wrapping a Haima 7

How much vinyl does it take to wrap a Haima 7?

A Haima 7 needs about 59 ft (18 m) of 60-inch (1.52 m) cast film for a full wrap. If you choose chrome or patterned film, expect to use about 69 ft (21 m) to match the pattern.

Can I wrap only the hood or the roof of a Haima 7?

Yes, you can wrap only the hood or the roof of a Haima 7. A partial wrap can cover the roof, hood, or mirror caps, while a chrome delete covers the window trim and badges.

Is a Haima 7 hard to wrap?

A Haima 7 is not especially hard to wrap, but it does add work in a few areas. Every trim has roof rails that must be removed or cut around. The parking sensors in the bumpers need the film cut around each sensor, and the tailgate glass stops the film at its edge.

How many generations of the Haima 7 does this page cover?

This page covers one generation of the Haima 7. It is the first generation SUV produced from 2013 to 2016.