Wraps by car

Honda Vigor wrap

The Honda Vigor wrap page covers the 1989–1995 third generation, the only generation in this catalog, and a full vinyl wrap of its sedan body takes about 51 ft (15.5 m) of 60-inch cast film.

1generations15.5 mof film for a full wrap

Honda Vigor, third generation, factory photo
Honda Vigor, third generation. Factory color shown.

Honda Vigor wrap colors and ideas

  • Vigor black wrap
  • Vigor white wrap
  • Vigor gray wrap
  • Vigor silver wrap
  • Vigor red wrap
  • Vigor blue wrap
  • Vigor green wrap
  • Vigor yellow wrap
  • Vigor orange wrap
  • Vigor purple wrap
  • Vigor pink wrap
  • Vigor teal wrap
  • Vigor brown wrap
  • Vigor gold wrap
  • Vigor chrome wrap
  • Vigor color shift wrap
  • Vigor carbon fiber wrap
  • Vigor camo and patterned wrap

How much vinyl to wrap a Honda Vigor

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1989–1995sedan (4 doors)184.6 in (4,690 mm)about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m)

Vigor wrap cost factors

Vigor wrap cost depends on the size of the sedan, the film line and the amount of chrome delete or partial coverage you choose. A full color change wrap for the 1989–1995 body takes about 51 ft (15.5 m) of 60-inch cast film, while patterned or chrome film takes about 64 ft (19.5 m). The cost also moves with the prep work the 184.6 in (4,690 mm) body needs after its production years, such as correcting paint or repairing a panel.

  • Film for a full wrap: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).
  • Body: sedan (4 doors).

Vigor wraps by generation

Swipe sideways. Tap a card for the full description.

Honda Vigor, third generation, factory photo
Factory color shown

1989–1995 Vigor sedan (third generation)

1989–1995sedan (4 doors)184.6 in (4,690 mm)

The 1989–1995 Honda Vigor is the third generation of the model and the only generation of this page, sold as a four-door sedan in CB and CC chassis codes. On a car of these years, panels may be original or repainted, and a test spot on the paint comes before a full wrap to check adhesion. The mid-size body is 184.6 in (4,690 mm) long, which sets the amount of vinyl a complete wrap consumes.

Film: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).

Roof, hood, chrome delete and PPF on a Vigor

A partial wrap on a Honda Vigor can cover the roof, the hood or the mirror caps, and a chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips without changing the color. These smaller jobs use less vinyl than a full wrap and are a way to change only one part of the sedan.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Honda Vigor: body, cut-outs and film

The Honda Vigor vinyl wrap is worked out on a mid-size sedan 184.6 in (4,690 mm) long, so every body side is a large flat panel plus a roof and four doors. A wrap uses more film than smaller sedans but no extra material for long doors or a tailgate. The four-door body keeps the wrap job straightforward with no long roof rails or a large rear hatch to cover.

Vigor wrap ideas start with the sedan's door handles, mirrors and the trim around the side windows, which are removed or cut out for a clean edge. The front and rear bumpers can stay on the car, but the wrap needs relief cuts around the fog light openings on some trims. The badges and the antenna base are small parts that a wrap installer covers or works around with separate pieces.

How much vinyl to wrap a Vigor does not change between generations because this page covers only the 1989–1995 CB and CC sedans, all built on the same body. Someone who counts film for a Vigor of that run measures the same sedan length of 184.6 in (4,690 mm) for every car. The film estimate of about 51 ft (15.5 m) of 60-inch cast film is for a standard color change on a complete sedan.

Questions about wrapping a Honda Vigor

How much vinyl does it take to wrap a Honda Vigor?

Yes, a full wrap of a 1989–1995 Honda Vigor sedan takes about 51 ft (15.5 m) of 60-inch cast film, which covers the outside panels in one color. The estimate is for the newest body in this catalog, the third generation, with a length of 184.6 in (4,690 mm). If you choose chrome or patterned film, the amount rises to about 64 ft (19.5 m).

Can I wrap only the hood or the roof of a Vigor?

Yes, you can wrap only the hood or the roof of a Vigor, and those are standard partial wrap jobs. The same goes for the mirror caps, while a chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is another partial option, a clear film on the front end to protect the paint.

Is a Vigor hard to wrap?

A Vigor is not a hard wrap for a four-door sedan, but the 184.6 in (4,690 mm) length means large side panels and a roof to handle in single pieces. The wrap adds work around the door handles, mirrors and side window trim, which are removed or cut out for a clean edge. On some trims, the fog light openings in the bumpers need relief cuts to fit the film without lifting.

How many generations of the Vigor does this page cover?

This page covers one generation of the Honda Vigor, the third generation produced from 1989 to 1995. The catalog holds only that body, a four-door sedan in CB and CC chassis codes.