Wraps by car

Lexus HS wrap

The Lexus HS is a mid-size sedan produced from 2009 to 2018, spanning one generation. A full wrap of this car requires about 57 ft (17.5 m) of 60-inch (1.52 m) cast vinyl film. If you choose chrome or patterned film, plan for about 67 ft (20.5 m). This guide covers what to expect when wrapping the Lexus HS.

1generations17.5 mof film for a full wrap

Lexus HS, first generation, factory photo
Lexus HS, first generation. Factory color shown.

Lexus HS wrap colors and ideas

  • Lexus HS black wrap
  • Lexus HS white wrap
  • Lexus HS gray wrap
  • Lexus HS silver wrap
  • Lexus HS red wrap
  • Lexus HS blue wrap
  • Lexus HS green wrap
  • Lexus HS yellow wrap
  • Lexus HS orange wrap
  • Lexus HS purple wrap
  • Lexus HS pink wrap
  • Lexus HS teal wrap
  • Lexus HS brown wrap
  • Lexus HS gold wrap
  • Lexus HS chrome wrap
  • Lexus HS color shift wrap
  • Lexus HS carbon fiber wrap
  • Lexus HS camo and patterned wrap

How much vinyl to wrap a Lexus HS

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2009–2018sedan (4 doors)184.6 in (4,690 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m)

Lexus HS wrap cost factors

The Lexus HS wrap cost depends mainly on the film type and the installer's labor. A full wrap uses about 57 ft (17.5 m) of cast film, and chrome or patterned films require about 67 ft (20.5 m). Removing and reinstalling parts like door handles and mirrors adds labor time. The sedan's four-door body also means extra work around the door jambs if you wrap inside them.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).
  • Body: sedan (4 doors).
  • Restyled in 2013: bumpers and lights differ between the versions, and so do the film cuts.

Lexus HS wraps by generation

Swipe sideways. Tap a card for the full description.

Lexus HS, first generation, factory photo
Factory color shown

2009–2018 Lexus HS sedan (first generation)

2009–2018sedan (4 doors)184.6 in (4,690 mm)

The first generation Lexus HS was made from 2009 to 2018 as a four-door sedan. Its length stayed at 184.6 in (4,690 mm) throughout production. In 2013, the car received a restyling with new bumpers and lights. That change means a film template cut for a pre-2013 car will not fit a later one properly.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 67 ft (20.5 m).

Roof, hood, chrome delete and PPF on a Lexus HS

A Lexus HS chrome delete covers the window trim and badges with black film, giving the car a sportier look. Partial wrap options include the roof, hood, and mirror caps for a two-tone effect. Paint protection film (PPF) is a clear option applied to the front end to guard against stone chips. These smaller jobs use less film and can be done without wrapping the entire car.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Lexus HS: body, cut-outs and film

The Lexus HS vinyl wrap covers a sedan body with four doors and a length of 184.6 in (4,690 mm). Its smooth, curved panels are typical for a mid-size sedan, but the rear bumper and trunk areas require careful stretching. The roof is large and relatively flat, which makes it a straightforward section to wrap. Overall, the body size means a full wrap uses less film than a larger luxury sedan.

For Lexus HS wrap ideas, plan for several areas that need extra work. The door handles, mirrors, and antenna should be removed or masked for a clean installation. The front bumper has multiple grille openings that require precise cutting and tucking. If you cover the window trim for a chrome delete, the trim pieces are thin and need careful knifeless tape work.

To figure out how much vinyl to wrap a Lexus HS, you only need measurements for one generation. The body style stayed consistent from 2009 to 2018, so the same film estimate applies to all years. However, the 2013 restyling changed the front and rear bumpers, so pre-cut kits are not interchangeable across that year. If you buy film by the roll, the total area remains the same.

Questions about wrapping a Lexus HS

How much vinyl does it take to wrap a Lexus HS?

It takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast vinyl to wrap a Lexus HS. If you use chrome or patterned film, plan for about 67 ft (20.5 m) because of additional waste from matching patterns.

Which years of the Lexus HS take the same film cuts?

All years from 2009 to 2018 share the same overall body shape, but the 2013 restyling changed the bumpers and lights. So film cuts for the front and rear bumpers are specific to either 2009–2012 or 2013–2018. The hood, roof, and doors can use the same cuts for all years.

Can I wrap only the hood or the roof of a Lexus HS?

Yes, you can wrap only the hood or the roof of a Lexus HS. A partial wrap is often done on the roof, hood, or mirror caps. A chrome delete on the window trim and badges is another popular smaller job.

Is a Lexus HS hard to wrap?

The Lexus HS is moderately difficult to wrap because of its front bumper design. The bumper has several grille openings and curves that require careful cutting and heating. The sedan's length of 184.6 in (4,690 mm) also means large panels like the roof need two people to handle the film without creasing.