Wraps by car

Audi 200 wrap

The Audi 200 wrap page covers the full-size Audi 200 from 1979 to 1991 across two generations. A complete vinyl wrap of the newest sedan body takes about 54 feet (16.5 meters) of 60-inch (1.52 meter) cast film. The wagon body of the same generation needs about 57 feet (17.5 meters).

2generations16.5 mof film for a full wrap

Audi 200, second generation, factory photo
Audi 200, second generation. Factory color shown.

Audi 200 wrap colors and ideas

  • Audi 200 black wrap
  • Audi 200 white wrap
  • Audi 200 gray wrap
  • Audi 200 silver wrap
  • Audi 200 red wrap
  • Audi 200 blue wrap
  • Audi 200 green wrap
  • Audi 200 yellow wrap
  • Audi 200 orange wrap
  • Audi 200 purple wrap
  • Audi 200 pink wrap
  • Audi 200 teal wrap
  • Audi 200 brown wrap
  • Audi 200 gold wrap
  • Audi 200 chrome wrap
  • Audi 200 color shift wrap
  • Audi 200 carbon fiber wrap
  • Audi 200 camo and patterned wrap

How much vinyl to wrap an Audi 200

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1983–1991sedan, wagon (4 or 5 doors)188.7 in (4,793 mm) to 189.3 in (4,807 mm)about 54 ft (16.5 m) for the sedan to 57 ft (17.5 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 74 ft (22.5 m)
1979–1983sedan (4 doors)184.3 in (4,680 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m)

Audi 200 wrap cost factors

The Audi 200 wrap cost depends on which generation and body you have, because the later wagon needs more film than the early sedan. A full wrap of the second-generation wagon uses about 57 feet (17.5 meters) of cast film, while the first-generation sedan needs about 52 feet (16 meters). The condition of the panels also affects cost, because older or repainted panels need more preparation before film is applied. Chrome delete and paint protection film are smaller jobs that cost less than a full color change wrap.

  • Film for a full wrap: about 54 ft (16.5 m) for the sedan to 57 ft (17.5 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 74 ft (22.5 m).
  • Body: sedan, wagon (4 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Restyled in 1988: bumpers and lights differ between the versions, and so do the film cuts.

Audi 200 wraps by generation

Swipe sideways. Tap a card for the full description.

Audi 200, second generation, factory photo
Factory color shown

1983–1991 Audi 200 sedan, wagon (second generation)

1983–1991sedan, wagon (4 or 5 doors)188.7 in (4,793 mm) to 189.3 in (4,807 mm)

The second-generation Audi 200 was restyled in 1988, with new bumpers and lights that changed the film cuts. A wrap kit made for a 1983 to 1987 car does not fit a 1988 to 1991 car on those panels. The body length stayed nearly the same at 188.7 to 189.3 inches (4,793 to 4,807 mm), so the hood, roof and doors are unchanged. Installers count the second generation as two versions for cutting film.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 54 ft (16.5 m) for the sedan to 57 ft (17.5 m) for the wagon, 60-inch (1.52 m) cast film; chrome or patterned film: up to about 74 ft (22.5 m).

Audi 200, first generation, factory photo
Factory color shown

1979–1983 Audi 200 sedan (first generation)

1979–1983sedan (4 doors)184.3 in (4,680 mm)

The first-generation Audi 200 from 1979 to 1983 has paint that may be original or repainted after four decades. A test spot is necessary before a full wrap because old paint can lift when the film is removed. The sedan body is 184.3 inches (4,680 mm) long and takes about 52 feet (16 meters) of 60-inch cast film. No restyling occurred in this generation, so one set of panel cuts fits all years.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).

Roof, hood, chrome delete and PPF on an Audi 200

A partial wrap on an Audi 200 can cover the roof, hood, or mirror caps without wrapping the whole car. An Audi 200 chrome delete covers the window trim and badges with black film to change the brightwork. Paint protection film (PPF) is a clear film applied to the front end of an Audi 200 to guard against stone chips. These smaller jobs need less film than a full wrap and can be done on any generation.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Audi 200: body, cut-outs and film

The Audi 200 was built as a four-door sedan in every generation, with a five-door wagon added from 1983. The second-generation sedan measures 188.7 to 189.3 inches (4,793 to 4,807 mm) long, so its panels are large but flat and straightforward to cover. The wagon adds a tailgate with the rear glass in it, where the film ends at the edge of the glass. An Audi 200 vinyl wrap on the sedan uses less film than the wagon, but both bodies are full-size cars with long roof sections.

The wagon tailgate is the main panel that needs careful cut-outs because the rear glass is set into it. The window trim and badges on every Audi 200 are small parts that can be wrapped or left in place. For a color change wrap, the door handles and mirrors stay on the car, but the installer trims around them precisely. The bumpers and lights changed with the 1988 restyling, so film cut for one version does not fit the other.

How much vinyl to wrap an Audi 200 depends on the generation and body style. The first-generation sedan from 1979 to 1983 is the shortest body at 184.3 inches (4,680 mm) and takes about 52 feet (16 meters) of 60-inch cast film. The second-generation sedan, built from 1983 to 1991, needs about 54 to 57 feet (16.5 to 17.5 meters) for the sedan or wagon. Chrome or patterned film on the same bodies uses about 64 to 74 feet (19.5 to 22.5 meters) because the pattern must be matched.

Questions about wrapping an Audi 200

How much vinyl does it take to wrap an Audi 200?

A full wrap of the newest Audi 200 sedan takes about 54 feet (16.5 meters) of 60-inch (1.52 meter) cast film. The wagon body of the same generation needs about 57 feet (17.5 meters), and chrome or patterned film adds up to about 74 feet (22.5 meters). The first-generation sedan from 1979 to 1983 uses about 52 feet (16 meters).

Which years of the Audi 200 take the same film cuts?

The same film cuts fit the Audi 200 within each production period before and after the 1988 restyling. The second-generation cars from 1983 to 1987 share one set of cuts, and the 1988 to 1991 cars share another because the bumpers and lights changed. The first-generation cars from 1979 to 1983 all take the same cuts because there was no restyling.

Which Audi 200 body takes more film?

The wagon body of the second-generation Audi 200 takes more film than the sedan. A full wrap of the wagon needs about 57 feet (17.5 meters) of 60-inch cast film, while the sedan of the same generation needs about 54 feet (16.5 meters). The first-generation sedan, which is the only body of those years, needs about 52 feet (16 meters).

Can I wrap only the hood or the roof of an Audi 200?

Yes, you can wrap only the hood or the roof of an Audi 200. A partial wrap on the roof, hood, or mirror caps is a smaller job that uses less film than a full color change wrap. Chrome delete on the window trim and badges, and paint protection film on the front end, are also available for any Audi 200 generation.