Wraps by car

Talbot Rancho wrap

This page covers the Talbot Rancho, a classic SUV produced from 1977 to 1984 in a single generation. A full vinyl wrap of the newest body takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, the amount rises to about 64 ft (19.5 m).

1generations17.5 mof film for a full wrap

Talbot Rancho, first generation, factory photo
Talbot Rancho, first generation. Factory color shown.

Talbot Rancho wrap colors and ideas

  • Rancho black wrap
  • Rancho white wrap
  • Rancho gray wrap
  • Rancho silver wrap
  • Rancho red wrap
  • Rancho blue wrap
  • Rancho green wrap
  • Rancho yellow wrap
  • Rancho orange wrap
  • Rancho purple wrap
  • Rancho pink wrap
  • Rancho teal wrap
  • Rancho brown wrap
  • Rancho gold wrap
  • Rancho chrome wrap
  • Rancho color shift wrap
  • Rancho carbon fiber wrap
  • Rancho camo and patterned wrap

How much vinyl to wrap a Talbot Rancho

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1977–1984SUV (3 doors)170.1 in (4,320 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m)

Rancho wrap cost factors

The Rancho wrap cost depends on the vehicle's size, the film type chosen, and the condition of the paintwork. A full wrap needs about 57 ft (17.5 m) of standard cast film or 64 ft (19.5 m) of chrome or patterned film. Surface preparation and any repairs to original or repainted panels also influence the final figure.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).
  • Body: SUV (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

Rancho wraps by generation

Swipe sideways. Tap a card for the full description.

Talbot Rancho, first generation, factory photo
Factory color shown

1977–1984 Rancho SUV (first generation)

1977–1984SUV (3 doors)170.1 in (4,320 mm)

The first generation Talbot Rancho from 1977 to 1984 often has original or repainted panels due to its age. Before a full wrap, a test spot on the paint checks whether the film adheres properly without lifting old coatings. This step prevents failures on older finishes and helps the installer plan surface preparation.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 64 ft (19.5 m).

Roof, hood, chrome delete and PPF on a Rancho

For a partial wrap on a Rancho, the roof, hood, and mirror caps can be covered separately to change the look without a full wrap. Rancho chrome delete involves covering the window trim and badges with black film. Paint protection film on the front end shields the nose from stone chips and scratches, applied as clear film.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Talbot Rancho: body, cut-outs and film

The Talbot Rancho vinyl wrap suits its boxy three-door SUV body, where large flat panels simplify film installation. The vehicle measures 170.1 in (4,320 mm) in length, a compact size that keeps material use moderate. Its tall roofline and upright sides mean installers can cover big areas with single pieces, reducing seams.

Rancho wrap ideas include working around the tailgate with rear glass in it, where the film must end at the edge of the glass. The two long side doors each take one large piece of film, which demands careful stretching and positioning. Removing door handles and mirrors before wrapping gives a cleaner finish around those openings.

To know how much vinyl to wrap a Rancho, note that the page covers only the first generation from 1977 to 1984. There are no other generations in the catalog, so film estimates stay the same across all years of this model. The body dimensions remained unchanged throughout the production run, keeping material calculations simple.

Questions about wrapping a Talbot Rancho

How much vinyl does it take to wrap a Talbot Rancho?

It takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film to wrap a Talbot Rancho. If you choose chrome or patterned film, plan for about 64 ft (19.5 m) instead. These figures are for the newest body of the only generation, produced from 1977 to 1984.

Can I wrap only the hood or the roof of a Rancho?

Yes, you can wrap only the hood or the roof of a Rancho. Partial wrap options include the roof, hood, and mirror caps, and you can also do a chrome delete on the window trim and badges. Paint protection film on the front end is another smaller job.

Is a Rancho hard to wrap?

A Rancho is moderately difficult to wrap because of its tailgate with rear glass in it, where the film must end at the edge of the glass. The two long side doors each need one large piece of film, which requires skill to avoid wrinkles and stretch marks. Its 170.1 in (4,320 mm) length is manageable, but the tall roof adds height to reach.

How many generations of the Rancho does this page cover?

This page covers one generation of the Rancho, the first generation from 1977 to 1984. There are no other generations in the catalog. All body styles and film estimates refer to that single generation.