Wraps by car

Tatra 57 wrap

The Tatra 57 wrap needs about 43 ft (13 m) of 60-inch (1.52 m) cast film for a full color change on this subcompact sedan. This page covers one generation of the Tatra 57, produced from 1932 to 1949. A vinyl wrap protects the old paint and gives the car a new look without a respray.

1generations13 mof film for a full wrap

Tatra 57, first generation, factory photo
Tatra 57, first generation. Factory color shown.

Tatra 57 wrap colors and ideas

  • Tatra 57 black wrap
  • Tatra 57 white wrap
  • Tatra 57 gray wrap
  • Tatra 57 silver wrap
  • Tatra 57 red wrap
  • Tatra 57 blue wrap
  • Tatra 57 green wrap
  • Tatra 57 yellow wrap
  • Tatra 57 orange wrap
  • Tatra 57 purple wrap
  • Tatra 57 pink wrap
  • Tatra 57 teal wrap
  • Tatra 57 brown wrap
  • Tatra 57 gold wrap
  • Tatra 57 chrome wrap
  • Tatra 57 color shift wrap
  • Tatra 57 carbon fiber wrap
  • Tatra 57 camo and patterned wrap

How much vinyl to wrap a Tatra 57

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1932–1949sedan (2 doors)137.8 in (3,500 mm)about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m)

Tatra 57 wrap cost factors

The Tatra 57 wrap cost depends on the film choice: cast film for the full body, or a chrome or patterned film that needs about 51 ft (15.5 m). The size of the car at 137.8 in (3,500 mm) long keeps the material use modest. Labor time rises with the number of cut-outs around the two long doors and trim. Paint condition matters too, because older or repainted panels need more preparation before the vinyl goes on.

  • Film for a full wrap: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).
  • Body: sedan (2 doors).
  • Two long side doors: each door is one large piece of film.

Tatra 57 wraps by generation

Swipe sideways. Tap a card for the full description.

Tatra 57, first generation, factory photo
Factory color shown

1932–1949 Tatra 57 sedan (first generation)

1932–1949sedan (2 doors)137.8 in (3,500 mm)

The first generation Tatra 57 was built from 1932 to 1949 as a two-door sedan. Paint age matters on these cars, because panels may be original or repainted. A test spot on each panel shows whether the old paint will hold the film or lift when the vinyl is removed. This step prevents damage when wrapping a car this old.

Two long side doors: each door is one large piece of film.

Film: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 51 ft (15.5 m).

Roof, hood, chrome delete and PPF on a Tatra 57

For a smaller job, a partial wrap on a Tatra 57 covers the roof, hood, or mirror caps. A chrome delete (bright trim covered with black film) works on the window trim and badges. Paint protection film (PPF) is a clear film for the front end to guard against stone chips. These options use less material than a full wrap and can refresh the car's look.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Tatra 57: body, cut-outs and film

A Tatra 57 vinyl wrap is a compact job because the car is only 137.8 in (3,500 mm) long with two doors. The two long side doors each take one large piece of film, which reduces the number of seams. The sedan body has no complex roof rails or hatch, so the main surfaces are straightforward to cover.

For Tatra 57 wrap ideas, focus on the long side doors and the rounded front fenders. The doors are large enough that a single piece of film can cover the entire panel for a clean look. The door handles, hinges, and trim need precise cut-outs. The fenders may be wrapped with the hood or separately, depending on the film layout.

If you want to know how much vinyl to wrap a Tatra 57, the estimate is about 43 ft (13 m) of 60-inch (1.52 m) cast film for a standard color change. This figure is for the first generation, the only body style covered here. A chrome or patterned film raises the estimate to about 51 ft (15.5 m) because of the laying direction and waste. The car was produced from 1932 to 1949, so panels may differ from early to late examples.

Questions about wrapping a Tatra 57

How much vinyl does it take to wrap a Tatra 57?

About 43 ft (13 m) of 60-inch (1.52 m) cast film is needed to wrap a Tatra 57. This estimate is for a full color change on the two-door sedan body. Chrome or patterned film raises the amount to about 51 ft (15.5 m) due to extra waste.

Can I wrap only the hood or the roof of a Tatra 57?

Yes, you can wrap only the hood or the roof of a Tatra 57. A partial wrap can cover the roof, hood, or mirror caps as separate jobs. These panels are small enough to use leftover film and cost less than a full wrap.

Is a Tatra 57 hard to wrap?

The Tatra 57 is not hard to wrap, but it has some extra work. The long side doors take one large piece of film each, which requires careful handling. The car's length of 137.8 in (3,500 mm) and simple sedan shape keep the process straightforward. Old paint may need a test spot before wrapping to check adhesion.

How many generations of the Tatra 57 does this page cover?

This page covers one generation of the Tatra 57, produced from 1932 to 1949. The catalog lists this single body style, a two-door sedan.