Wraps by car

Land Rover Series I wrap

The Land Rover Series I wrap page covers the first generation produced from 1948 to 1956 as a three-door SUV. A full vinyl wrap of the newest body takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, the estimate rises to about 70 ft (21.5 m).

1generations17.5 mof film for a full wrap

Land Rover Series I, first generation, factory photo
Land Rover Series I, first generation. Factory color shown.

Land Rover Series I wrap colors and ideas

  • Series I black wrap
  • Series I white wrap
  • Series I gray wrap
  • Series I silver wrap
  • Series I red wrap
  • Series I blue wrap
  • Series I green wrap
  • Series I yellow wrap
  • Series I orange wrap
  • Series I purple wrap
  • Series I pink wrap
  • Series I teal wrap
  • Series I brown wrap
  • Series I gold wrap
  • Series I chrome wrap
  • Series I color shift wrap
  • Series I carbon fiber wrap
  • Series I camo and patterned wrap

How much vinyl to wrap a Land Rover Series I

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1948–1956SUV (3 doors)173.5 in (4,407 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m)

Series I wrap cost factors

Series I wrap cost depends on the size of the body, the film type, and the labor for the tall roof. This SUV measures 173.5 in (4,407 mm) long and 73.5 in (1,867 mm) high, so the roof work takes extra time. A chrome or patterned film uses about 70 ft (21.5 m) compared to about 57 ft (17.5 m) for standard cast film.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).
  • Body: SUV (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.
  • A tall body (73.5 in (1,867 mm)): the roof is wrapped from a platform.

Series I wraps by generation

Swipe sideways. Tap a card for the full description.

Land Rover Series I, first generation, factory photo
Factory color shown

1948–1956 Series I SUV (first generation)

1948–1956SUV (3 doors)173.5 in (4,407 mm)

The first generation of the Land Rover Series I has a tall body of 73.5 in (1,867 mm). The roof is wrapped from a platform, which adds to the installation time. This height is a key consideration for anyone planning a full wrap.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

A tall body (73.5 in (1,867 mm)): the roof is wrapped from a platform.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).

Roof, hood, chrome delete and PPF on a Series I

A partial wrap on a Land Rover Series I can cover the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear option for the front end only.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Land Rover Series I: body, cut-outs and film

A Land Rover Series I vinyl wrap must follow the simple boxy body of this 173.5 in (4,407 mm) long three-door SUV. The tall 73.5 in (1,867 mm) body means the roof is wrapped from a platform. Each of the two long side doors is covered with one large piece of film. The tailgate includes the rear glass, so the film ends at the edge of that glass.

Series I wrap ideas start with noting which parts need cut-outs or come off for a clean install. The tailgate has the rear glass built in, and the film stops at the glass edge. The two long side doors are wrapped as single large panels. For the roof, a platform is required because of the body height.

Knowing how much vinyl to wrap a Series I depends on the generation covered here. The only generation in this catalog is the first one, from 1948 to 1956. The body size is consistent within this generation, so the film estimate stays the same.

Questions about wrapping a Land Rover Series I

How much vinyl does it take to wrap a Land Rover Series I?

It takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film to wrap a Land Rover Series I. For chrome or patterned film, the amount is about 70 ft (21.5 m). These figures are for the newest body of the first generation.

Can I wrap only the hood or the roof of a Series I?

You can wrap only the hood or the roof of a Series I as a partial job. The roof wrap requires a platform because of the body height. The hood is a straightforward single panel.

Is a Series I hard to wrap?

A Series I is more work to wrap than a smaller car because of its tall body. The roof height of 73.5 in (1,867 mm) means installers need a platform. The tailgate with rear glass and the long doors also require careful film cutting.

How many generations of the Series I does this page cover?

This page covers one generation of the Land Rover Series I, produced from 1948 to 1956. The body style remains a three-door SUV throughout that period.