Wraps by car

Adler Trumpf Sport wrap

An Adler Trumpf Sport wrap covers the complete 1933–1935 convertible body with a color change vinyl wrap. The catalog lists one generation, and a full wrap of the open two-door body takes about 52 ft (16 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds material, bringing the total to about 59 ft (18 m).

1generations16 mof film for a full wrap

Adler Trumpf Sport, first generation, factory photo
Adler Trumpf Sport, first generation. Factory color shown.

Adler Trumpf Sport wrap colors and ideas

  • Trumpf Sport black wrap
  • Trumpf Sport white wrap
  • Trumpf Sport gray wrap
  • Trumpf Sport silver wrap
  • Trumpf Sport red wrap
  • Trumpf Sport blue wrap
  • Trumpf Sport green wrap
  • Trumpf Sport yellow wrap
  • Trumpf Sport orange wrap
  • Trumpf Sport purple wrap
  • Trumpf Sport pink wrap
  • Trumpf Sport teal wrap
  • Trumpf Sport brown wrap
  • Trumpf Sport gold wrap
  • Trumpf Sport chrome wrap
  • Trumpf Sport color shift wrap
  • Trumpf Sport carbon fiber wrap
  • Trumpf Sport camo and patterned wrap

How much vinyl to wrap an Adler Trumpf Sport

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1933–1935convertible (2 doors)178.7 in (4,540 mm)about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m)

Trumpf Sport wrap cost factors

Trumpf Sport wrap cost depends on the film type, the extent of the wrap, and the convertible body. A full color change needs about 52 ft (16 m) of 60-inch (1.52 m) cast film, while chrome or patterned film raises the amount to about 59 ft (18 m). The 178.7 in (4,540 mm) length and two-door layout require precise trimming around the open top. Cutting around the fabric roof, door handles, and badges adds labor.

  • Film for a full wrap: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Trumpf Sport wraps by generation

Swipe sideways. Tap a card for the full description.

Adler Trumpf Sport, first generation, factory photo
Factory color shown

1933–1935 Trumpf Sport convertible (first generation)

1933–1935convertible (2 doors)178.7 in (4,540 mm)

The open top of the 1933–1935 Trumpf Sport is left uncovered in a wrap. A fabric top is not wrapped, and the film ends where it begins, following the body line. A folding hard top, if the car has one, is wrapped as panels of its own. The film never bridges from the body onto the top.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 52 ft (16 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 59 ft (18 m).

Roof, hood, chrome delete and PPF on a Trumpf Sport

A partial wrap on a Trumpf Sport can cover the hood, mirror caps, or rear deck. Chrome delete on this car means covering the window trim and badges with black film. Paint protection film (PPF) is applied as clear film on the front end. These smaller jobs use less material than a full wrap.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping an Adler Trumpf Sport: body, cut-outs and film

An Adler Trumpf Sport vinyl wrap must follow the short convertible body, which measures 178.7 in (4,540 mm) in length. The fabric top is not wrapped, so the film ends where the roof begins. The subcompact size keeps material needs low, but the two-door layout leaves every panel exposed. Installers plan seams along the doors and rear deck for a clean finish.

Trumpf Sport wrap ideas start with the convertible shape, where the fabric top is left uncovered and the film ends at its edge. The wrap film is cut around the door handles, badges, and trim rather than removed. A folding hard top, if fitted, is wrapped as its own panels. The rear deck and hood need relief cuts at their hinges and latches.

To know how much vinyl to wrap a Trumpf Sport, compare the single generation's convertible body from 1933–1935. The factory dimensions stay the same across those years, so the film estimate does not change. The 52 ft (16 m) figure covers the painted metal, while chrome or patterned film needs about 59 ft (18 m). The fabric top is never part of the material count.

Questions about wrapping an Adler Trumpf Sport

How much vinyl does it take to wrap an Adler Trumpf Sport?

About 52 ft (16 m) of 60-inch (1.52 m) cast film wraps an Adler Trumpf Sport. Chrome or patterned film takes about 59 ft (18 m). The fabric top is not wrapped, so the film estimate covers the painted body only.

Is the top of a Trumpf Sport wrapped?

No, the top of a Trumpf Sport is not wrapped. A fabric top is left uncovered and the film ends where it begins. A folding hard top, if fitted, is wrapped as panels of its own.

Can I wrap only the hood or the roof of a Trumpf Sport?

Yes, you can wrap only the hood or the rear deck of a Trumpf Sport. A partial wrap on this car can cover the hood, mirror caps, or rear deck. The roof is not wrapped because the fabric top is left uncovered.

Is a Trumpf Sport hard to wrap?

Yes, a Trumpf Sport is harder to wrap than a fixed-roof car. The fabric top is not wrapped and the film must end cleanly where it begins. The 178.7 in (4,540 mm) body is short, but cutting around the open top, door handles, and trim adds work.