Wraps by car

BYD L3 wrap

The BYD L3 wrap page covers the compact sedan built from 2010 to 2015, the single generation listed in the catalog. A full vinyl wrap of the newest body takes about 56 ft (17 m) of 60-inch (1.52 m) cast film.

1generations17 mof film for a full wrap

BYD L3, first generation, factory photo
BYD L3, first generation. Factory color shown.

BYD L3 wrap colors and ideas

  • BYD L3 black wrap
  • BYD L3 white wrap
  • BYD L3 gray wrap
  • BYD L3 silver wrap
  • BYD L3 red wrap
  • BYD L3 blue wrap
  • BYD L3 green wrap
  • BYD L3 yellow wrap
  • BYD L3 orange wrap
  • BYD L3 purple wrap
  • BYD L3 pink wrap
  • BYD L3 teal wrap
  • BYD L3 brown wrap
  • BYD L3 gold wrap
  • BYD L3 chrome wrap
  • BYD L3 color shift wrap
  • BYD L3 carbon fiber wrap
  • BYD L3 camo and patterned wrap

How much vinyl to wrap a BYD L3

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2010–2015sedan (4 doors)179.8 in (4,568 mm)about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m)

BYD L3 wrap cost factors

BYD L3 wrap cost depends on the area of the four door panels, the roof, and the front and rear bumpers, plus the labor to remove door handles and mirrors. A chrome or patterned film needs about 66 ft (20 m) instead of 56 ft (17 m), so the film choice changes the amount of material. The condition of the paint also matters because a test spot is needed before a full wrap on a car of these years.

  • Film for a full wrap: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).
  • Body: sedan (4 doors).

BYD L3 wraps by generation

Swipe sideways. Tap a card for the full description.

BYD L3, first generation, factory photo
Factory color shown

2010–2015 BYD L3 sedan (first generation)

2010–2015sedan (4 doors)179.8 in (4,568 mm)

The first generation BYD L3 from 2010 to 2015 may have original or repainted panels, so paint age is a real concern for wrapping. A test spot on a lower panel shows whether the paint will hold the film or lift when the vinyl is repositioned. Any wrap installer who works on a car of these years has to check paint condition before quoting a full wrap.

Film: about 56 ft (17 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 66 ft (20 m).

Roof, hood, chrome delete and PPF on a BYD L3

Partial wrap on a BYD L3 can cover the roof, hood, or mirror caps when a full wrap is not needed. Chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a BYD L3: body, cut-outs and film

The BYD L3 vinyl wrap has to fit a four-door sedan body that is 179.8 in (4,568 mm) long. The four doors and the large roof panel are the main surfaces, but the trunk lid and bumpers also add area. A compact sedan like this uses less film than an SUV, yet every recess and curve still needs careful stretching and relief cuts.

BYD L3 wrap ideas have to account for door handles, side mirrors, and a front grille that need cut-outs or removal. The bumpers are best wrapped off the car for clean edges, while badges are taken off before the film goes on. The window trim is also a part that needs cut-outs or comes off when you plan a chrome delete.

How much vinyl to wrap a BYD L3 depends on the generation, but this page covers only the first generation from 2010 to 2015. The body shape stayed the same through those years, so the film estimate does not change between production runs. Someone who counts film for this car does not need to allow for different dimensions.

Questions about wrapping a BYD L3

How much vinyl does it take to wrap a BYD L3?

It takes about 56 ft (17 m) of 60-inch (1.52 m) cast film to wrap a BYD L3. The estimate is for the first generation sedan body. If you use chrome or patterned film, the amount goes up to about 66 ft (20 m) because the pattern must be matched.

Can I wrap only the hood or the roof of a BYD L3?

Yes, you can wrap only the hood or the roof of a BYD L3. A partial wrap is a smaller job that may cover the roof, hood, or mirror caps. The hood and roof are fairly flat on this sedan, so they are easier to wrap than the bumpers.

Is a BYD L3 hard to wrap?

The BYD L3 is not especially hard to wrap, but the door handles, side mirrors, and front grille add work. The bumpers are best removed for a clean install, which takes more time. The paint may be original or repainted on a car of these years, so a test spot is needed before a full wrap.

How many generations of the BYD L3 does this page cover?

This page covers one generation of the BYD L3, the first generation from 2010 to 2015. The body stayed the same through those production years, so the wrap data apply to every L3 of that period.