Wraps by car

Rolls-Royce Camargue wrap

The Rolls-Royce Camargue wrap page covers this full-size luxury coupe produced from 1975 to 1986 in one generation. A complete vinyl wrap of the Camargue takes about 62 ft (19 m) of 60-inch (1.52 m) cast film. For chrome or patterned film, plan for about 74 ft (22.5 m).

1generations19 mof film for a full wrap

Rolls-Royce Camargue, first generation, factory photo
Rolls-Royce Camargue, first generation. Factory color shown.

Rolls-Royce Camargue wrap colors and ideas

  • Camargue black wrap
  • Camargue white wrap
  • Camargue gray wrap
  • Camargue silver wrap
  • Camargue red wrap
  • Camargue blue wrap
  • Camargue green wrap
  • Camargue yellow wrap
  • Camargue orange wrap
  • Camargue purple wrap
  • Camargue pink wrap
  • Camargue teal wrap
  • Camargue brown wrap
  • Camargue gold wrap
  • Camargue chrome wrap
  • Camargue color shift wrap
  • Camargue carbon fiber wrap
  • Camargue camo and patterned wrap

How much vinyl to wrap a Rolls-Royce Camargue

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1975–1986sedan (2 doors)203.5 in (5,169 mm)about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m)

Camargue wrap cost factors

Camargue wrap cost depends on the size of the car, the film type, and the condition of the paint. At 203.5 in (5,169 mm) long, the Camargue requires more film than a smaller coupe, increasing labor time. A chrome or patterned film uses about 74 ft (22.5 m), which adds material cost.

  • Film for a full wrap: about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m).
  • Body: sedan (2 doors).
  • Two long side doors: each door is one large piece of film.

Camargue wraps by generation

Swipe sideways. Tap a card for the full description.

Rolls-Royce Camargue, first generation, factory photo
Factory color shown

1975–1986 Camargue sedan (first generation)

1975–1986sedan (2 doors)203.5 in (5,169 mm)

The first generation Camargue from 1975 to 1986 may have original or repainted panels. Before a full wrap, a test spot on the paint ensures the film adheres properly without lifting old paint. On a car of these years, wrap installers check each panel for rust or uneven paint before applying film.

Two long side doors: each door is one large piece of film.

Film: about 62 ft (19 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 74 ft (22.5 m).

Roof, hood, chrome delete and PPF on a Camargue

A partial wrap on a Camargue can cover the roof, hood, or mirror caps instead of the whole car. Camargue chrome delete covers the window trim and badges with black film for a darker look. Paint protection film (PPF) on the front end uses clear film to shield the hood and bumper from stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Rolls-Royce Camargue: body, cut-outs and film

A Rolls-Royce Camargue vinyl wrap must handle a long two-door sedan body measuring 203.5 in (5,169 mm) in length. The long hood and large rear quarters add surface area compared to smaller coupes. Each of the two long side doors is wrapped as one large piece, so careful film handling is required to avoid creases.

Camargue wrap ideas can include a full color change or an accent on the long doors. The two doors are the main large panels, and each takes one piece of film with no cut-outs for handles. For a full wrap, remove the door handles and trim to hide film edges cleanly.

To calculate how much vinyl to wrap a Camargue, note that only one generation exists from 1975 to 1986. The body dimensions stay the same across those years, so the film estimate is consistent. If you are ordering film for a full wrap, the figure of about 62 ft (19 m) applies to every Camargue.

Questions about wrapping a Rolls-Royce Camargue

How much vinyl does it take to wrap a Rolls-Royce Camargue?

A full wrap of a Rolls-Royce Camargue takes about 62 ft (19 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, the amount increases to about 74 ft (22.5 m). These figures apply to the single generation from 1975 to 1986.

Can I wrap only the hood or the roof of a Camargue?

Yes, you can wrap only the hood or the roof of a Camargue. Partial wrap options include the roof, hood, or mirror caps, and you can also do a chrome delete on the window trim and badges. Paint protection film on the front end is another partial job for clear protection.

Is a Camargue hard to wrap?

A Camargue wrap is challenging because the car is long and has large door panels. The two side doors each require one large piece of film, which demands careful stretching and squeegeeing to avoid wrinkles. The overall length of 203.5 in (5,169 mm) means more film handling than on a smaller coupe.

How many generations of the Camargue does this page cover?

This page covers one generation of the Camargue, produced from 1975 to 1986. Rolls-Royce did not redesign the Camargue during its run, so there is only a first generation.