Wraps by car

SEAT 133 wrap

The SEAT 133 wrap page covers the single generation of this mini hatchback produced from 1974 to 1979. A full vinyl wrap of the SEAT 133 takes about 41 ft (12.5 m) of 60-inch (1.52 m) cast film. The car's small size and simple three-door body make it a compact wrapping project.

1generations12.5 mof film for a full wrap

SEAT 133, first generation, factory photo
SEAT 133, first generation. Factory color shown.

SEAT 133 wrap colors and ideas

  • SEAT 133 black wrap
  • SEAT 133 white wrap
  • SEAT 133 gray wrap
  • SEAT 133 silver wrap
  • SEAT 133 red wrap
  • SEAT 133 blue wrap
  • SEAT 133 green wrap
  • SEAT 133 yellow wrap
  • SEAT 133 orange wrap
  • SEAT 133 purple wrap
  • SEAT 133 pink wrap
  • SEAT 133 teal wrap
  • SEAT 133 brown wrap
  • SEAT 133 gold wrap
  • SEAT 133 chrome wrap
  • SEAT 133 color shift wrap
  • SEAT 133 carbon fiber wrap
  • SEAT 133 camo and patterned wrap

How much vinyl to wrap an SEAT 133

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1974–1979hatchback (3 doors)135.9 in (3,451 mm)about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m)

SEAT 133 wrap cost factors

SEAT 133 wrap cost depends on the size of the car, the film you choose, and the condition of the paint. This car is only 135.9 in (3,451 mm) long, so it needs less film than a larger vehicle, but the two long doors and tailgate add labor. A chrome or patterned film raises the material use to about 46 ft (14 m), which also affects the cost.

  • Film for a full wrap: about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).
  • Body: hatchback (3 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.
  • Two long side doors: each door is one large piece of film.

SEAT 133 wraps by generation

Swipe sideways. Tap a card for the full description.

SEAT 133, first generation, factory photo
Factory color shown

1974–1979 SEAT 133 hatchback (first generation)

1974–1979hatchback (3 doors)135.9 in (3,451 mm)

The first generation SEAT 133 was built from 1974 to 1979 as a three-door hatchback. Paint age is a key factor on these cars because panels may be original or repainted, and a test spot comes before a full wrap. The body is small at 135.9 in (3,451 mm), which means a full wrap takes about 41 ft (12.5 m) of 60-inch (1.52 m) cast film.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Two long side doors: each door is one large piece of film.

Film: about 41 ft (12.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 46 ft (14 m).

Roof, hood, chrome delete and PPF on an SEAT 133

Partial wrap options for the SEAT 133 include the roof, hood, and mirror caps. A chrome delete covers the window trim and badges with black film, and paint protection film can be applied to the front end. These jobs use less film than a full wrap while still changing the car's look.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping an SEAT 133: body, cut-outs and film

A SEAT 133 vinyl wrap is a small job because the car is only 135.9 in (3,451 mm) long with a hatchback body and three doors. The two long side doors are each one large piece of film, which speeds up installation. The tailgate has the rear glass in it, so the film ends at the edge of the glass and no separate glass cut-out is needed.

SEAT 133 wrap ideas include a color change wrap, chrome delete (bright trim covered with black film), and paint protection film (PPF) on the front end. The tailgate needs a precise cut around the rear glass because the film ends at its edge. The side doors require large, single panels that must be laid smoothly without wrinkles.

How much vinyl to wrap an SEAT 133 depends on the film type and the wrap coverage. A full wrap of the first generation uses about 41 ft (12.5 m) of standard 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for about 46 ft (14 m) because of pattern matching and extra waste.

Questions about wrapping an SEAT 133

How much vinyl does it take to wrap an SEAT 133?

It takes about 41 ft (12.5 m) of 60-inch (1.52 m) cast film to wrap an SEAT 133. That figure covers the whole exterior of the first generation hatchback. For chrome or patterned film, allow about 46 ft (14 m) because of extra waste.

Can I wrap only the hood or the roof of an SEAT 133?

Yes, you can wrap only the hood or the roof of an SEAT 133. A partial wrap can cover the roof, hood, or mirror caps, and you can also do a chrome delete on the window trim and badges. Paint protection film on the front end is another common smaller job.

Is an SEAT 133 hard to wrap?

The SEAT 133 is not hard to wrap because it is a small car with a simple three-door hatchback body. The two long side doors are each one large piece of film, which adds some work because they must be applied smoothly. The tailgate has the rear glass in it, so the film ends at the edge of the glass and needs a precise cut.

How many generations of the SEAT 133 does this page cover?

This page covers one generation of the SEAT 133. The first generation was produced from 1974 to 1979 as a three-door hatchback.