Wraps by car

SEAT Fura wrap

The SEAT Fura wrap guide covers this subcompact hatchback from its first generation, produced from 1982 to 1986. A full vinyl wrap of the newest body takes about 43 ft (13 m) of 60-inch (1.52 m) cast film.

1generations13 mof film for a full wrap

SEAT Fura, first generation, factory photo
SEAT Fura, first generation. Factory color shown.

SEAT Fura wrap colors and ideas

  • Fura black wrap
  • Fura white wrap
  • Fura gray wrap
  • Fura silver wrap
  • Fura red wrap
  • Fura blue wrap
  • Fura green wrap
  • Fura yellow wrap
  • Fura orange wrap
  • Fura purple wrap
  • Fura pink wrap
  • Fura teal wrap
  • Fura brown wrap
  • Fura gold wrap
  • Fura chrome wrap
  • Fura color shift wrap
  • Fura carbon fiber wrap
  • Fura camo and patterned wrap

How much vinyl to wrap an SEAT Fura

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1982–1986hatchback (3 or 5 doors)146.4 in (3,718 mm)about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m)

Fura wrap cost factors

Fura wrap cost depends on the film type, the condition of the paint, and the number of panels you cover. A full wrap needs about 43 ft (13 m) of cast film, while chrome or patterned film uses about 54 ft (16.5 m). The small body means less material than a larger car, but old paint may need correction first.

  • Film for a full wrap: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).
  • Body: hatchback (3 or 5 doors).
  • A tailgate with the rear glass in it: the film ends at the edge of the glass.

Fura wraps by generation

Swipe sideways. Tap a card for the full description.

SEAT Fura, first generation, factory photo
Factory color shown

1982–1986 Fura hatchback (first generation)

1982–1986hatchback (3 or 5 doors)146.4 in (3,718 mm)

The first-generation Fura, built from 1982 to 1986, often has original or repainted panels because of its age. Before a full wrap, the installer should do a test spot to check how the film adheres to the old finish. On a car of these years, bodywork flaws may need filling so the wrap lays smooth.

A tailgate with the rear glass in it: the film ends at the edge of the glass.

Film: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).

Roof, hood, chrome delete and PPF on a Fura

A partial wrap on the Fura can cover the roof, hood, or mirror caps to change the look without a full wrap. You can also do a chrome delete, which means covering the bright window trim and badges with black film. For protection, clear paint protection film (PPF) can be applied to the front end.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping an SEAT Fura: body, cut-outs and film

The SEAT Fura vinyl wrap deals with a short hatchback body that is 146.4 in (3,718 mm) long and comes with either three or five doors. Its small size keeps the total film area low, while the extra doors on the five-door add little film. The three-door has longer front doors, which can make handling the large side panels slightly easier.

For Fura wrap ideas, the tailgate has the rear glass set into it, so the film ends at the edge of the glass. The door handles, side mirrors, and badges should be removed or masked for a clean install. The bumpers are simple shapes that wrap without deep recesses.

When you ask how much vinyl to wrap a Fura, this page covers the only generation, built from 1982 to 1986. Because there is one body style, the film estimate does not change between generations. You can use the same 43 ft (13 m) figure for any hatchback Fura.

Questions about wrapping an SEAT Fura

How much vinyl does it take to wrap an SEAT Fura?

A full wrap of an SEAT Fura takes about 43 ft (13 m) of 60-inch (1.52 m) cast film. If you choose chrome or patterned film, plan for about 54 ft (16.5 m) because of extra trimming.

Can I wrap only the hood or the roof of a Fura?

Yes, you can wrap only the hood or the roof of a Fura, and a partial wrap often covers those panels. Mirror caps are another small job, or you can protect the front end with clear paint protection film.

Is a Fura hard to wrap?

A Fura is not hard to wrap, but the tailgate with its inset rear glass adds work because the film must end at the glass edge. The small 146.4 in (3,718 mm) body and simple bumpers make most panels quick to cover.

How many generations of the Fura does this page cover?

This page covers one generation of the Fura, produced from 1982 to 1986. There are no other generations in the catalog.