Wraps by car

Daihatsu Xenia wrap

The Daihatsu Xenia wrap page covers the first-generation minivan made from 2003 to 2011. A full vinyl wrap of this five-door van takes about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. The film estimate is lower with standard cast film and rises to roughly 69 ft (21 m) when you choose chrome or patterned film.

1generations17.5 mof film for a full wrap

Daihatsu Xenia, first generation, factory photo
Daihatsu Xenia, first generation. Factory color shown.

Daihatsu Xenia wrap colors and ideas

  • Xenia black wrap
  • Xenia white wrap
  • Xenia gray wrap
  • Xenia silver wrap
  • Xenia red wrap
  • Xenia blue wrap
  • Xenia green wrap
  • Xenia yellow wrap
  • Xenia orange wrap
  • Xenia purple wrap
  • Xenia pink wrap
  • Xenia teal wrap
  • Xenia brown wrap
  • Xenia gold wrap
  • Xenia chrome wrap
  • Xenia color shift wrap
  • Xenia carbon fiber wrap
  • Xenia camo and patterned wrap

How much vinyl to wrap a Daihatsu Xenia

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2003–2011van (5 doors)160.2 in (4,070 mm)about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)

Xenia wrap cost factors

Xenia wrap cost depends on the area you cover and the film you choose. A full wrap on this van uses about 57 ft (17.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film pushes the amount to about 69 ft (21 m). Partial jobs like a roof, hood, or mirror caps use less material, and a chrome delete on window trim and badges is a smaller task.

  • Film for a full wrap: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: van (5 doors).
  • Sliding side doors: the door tracks stay bare, and the film is cut along them.

Xenia wraps by generation

Swipe sideways. Tap a card for the full description.

Daihatsu Xenia, first generation, factory photo
Factory color shown

2003–2011 Xenia van (first generation)

2003–2011van (5 doors)160.2 in (4,070 mm)

The first-generation Daihatsu Xenia has sliding side doors that shape the wrap work. The door tracks stay bare, and the film is cut along them, so the installer works around the track edges. This van is 160.2 in (4,070 mm) long, which gives a large side area to film. The five-door layout means you wrap the rear hatch and the sliding side doors as separate panels.

Sliding side doors: the door tracks stay bare, and the film is cut along them.

Film: about 57 ft (17.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Roof, hood, chrome delete and PPF on a Xenia

For a partial wrap on a Xenia, you can cover the roof, hood, or mirror caps. A chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear film option for the front end. These jobs use less film than a full wrap and let you change the look of one area.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Daihatsu Xenia: body, cut-outs and film

A Daihatsu Xenia vinyl wrap is shaped by the van body and its sliding side doors. The van is 160.2 in (4,070 mm) long, so you use film in large, simple panels. The sliding door tracks stay bare, and the film is cut along them. The tall, flat sides of a minivan give the installer long straight runs to work with.

Xenia wrap ideas start with roof, hood, and mirror caps when you want a smaller job. The sliding side door tracks need careful cutting because the tracks stay bare. Window trim and badges can be covered with black film as a chrome delete. The front end can take clear paint protection film (PPF) if you want protection without color change.

When you ask how much vinyl to wrap a Xenia, the answer is about 57 ft (17.5 m) of 60-inch (1.52 m) film. The first generation is the only one in this catalog, so the figure stays the same for all 2003–2011 vans. You would plan for about 69 ft (21 m) if you pick a chrome or patterned film. The sliding door tracks do not change the film amount but they do change the cutting pattern.

Questions about wrapping a Daihatsu Xenia

How much vinyl does it take to wrap a Daihatsu Xenia?

A Daihatsu Xenia needs about 57 ft (17.5 m) of 60-inch (1.52 m) cast film for a full wrap. That figure is for a standard color change on the first-generation van. With chrome or patterned film, the estimate rises to about 69 ft (21 m).

Are the sliding doors of a Xenia wrapped?

Yes, the sliding doors of a Xenia are wrapped, but the tracks stay bare. The film is cut along the door tracks so the doors still slide freely. The tracks act as a natural break line for the vinyl on the side panels.

Can I wrap only the hood or the roof of a Xenia?

Yes, you can wrap only the hood or the roof of a Xenia. The same goes for mirror caps as a partial wrap. You can also do a chrome delete on the window trim and badges or put paint protection film on the front end.

Is a Xenia hard to wrap?

A Xenia is not hard to wrap if you plan for the sliding door tracks. The tracks stay bare, so the film must be cut along them, which adds time. The van is 160.2 in (4,070 mm) long, so the side panels are tall and wide. Those large flat areas are easy to film once the edges are trimmed.