Wraps by car

McLaren F1 wrap

The McLaren F1 wrap page covers the single generation built from 1992 to 2000. A full vinyl wrap of this coupe needs about 43 ft (13 m) of 60-inch (1.52 m) cast film. Choosing chrome or patterned film raises the amount to roughly 54 ft (16.5 m) for complete coverage.

1generations13 mof film for a full wrap

McLaren F1, first generation, factory photo
McLaren F1, first generation. Factory color shown.

McLaren F1 wrap colors and ideas

  • McLaren F1 black wrap
  • McLaren F1 white wrap
  • McLaren F1 gray wrap
  • McLaren F1 silver wrap
  • McLaren F1 red wrap
  • McLaren F1 blue wrap
  • McLaren F1 green wrap
  • McLaren F1 yellow wrap
  • McLaren F1 orange wrap
  • McLaren F1 purple wrap
  • McLaren F1 pink wrap
  • McLaren F1 teal wrap
  • McLaren F1 brown wrap
  • McLaren F1 gold wrap
  • McLaren F1 chrome wrap
  • McLaren F1 color shift wrap
  • McLaren F1 carbon fiber wrap
  • McLaren F1 camo and patterned wrap

How much vinyl to wrap a McLaren F1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1992–2000coupe (2 doors)168.8 in (4,288 mm)about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m)

McLaren F1 wrap cost factors

The McLaren F1 wrap cost depends on the film type, the condition of the paint, and the amount of disassembly needed. A full color change on this 168.8 in (4,288 mm) coupe uses about 43 ft (13 m) of 60-inch (1.52 m) cast film, while chrome or patterned film uses about 54 ft (16.5 m). Removing the doors' large single-piece skins and refitting them adds labor. Any panel repainted over the car's life needs a test spot before full wrapping.

  • Film for a full wrap: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

McLaren F1 wraps by generation

Swipe sideways. Tap a card for the full description.

McLaren F1, first generation, factory photo
Factory color shown

1992–2000 McLaren F1 coupe (first generation)

1992–2000coupe (2 doors)168.8 in (4,288 mm)

The first-generation McLaren F1 was built from 1992 to 2000 as a two-door coupe. Paint age is a real factor on these cars because panels may be original or have been repainted over the decades. A test spot on each panel shows whether the paint will hold a wrap safely. This step is done before the full wrap so the film does not lift or damage old paint.

Two long side doors: each door is one large piece of film.

Film: about 43 ft (13 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 54 ft (16.5 m).

Roof, hood, chrome delete and PPF on a McLaren F1

Partial wrap options for the McLaren F1 include the roof, hood, and mirror caps in a contrasting color. A chrome delete covers the window trim and badges with black film, changing the car's brightwork without a full wrap. Paint protection film (PPF) applies clear film on the front end to guard against stone chips. Each of these jobs uses less film than a complete color change wrap.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a McLaren F1: body, cut-outs and film

A McLaren F1 vinyl wrap is shaped by the car's compact 168.8 in (4,288 mm) length and two-door coupe body. The low, wide stance means less surface area than a long sedan but more complex curves on every panel. A professional installer works with the car's tight shut lines and the absence of flat sections. Planning film seams on such a small body requires care around the rear haunches.

McLaren F1 wrap ideas start with the two long side doors, each door being one large piece of film. The door skins wrap around the edges and into the deep side intakes, so cut-outs must follow those lines accurately. The roof, hood, and engine cover come off for edge wrapping on this car. Removing the mirror caps helps a seamless finish around their slim bases.

There is only one generation, so how much vinyl to wrap a McLaren F1 does not change between body styles. Every 1992–2000 car uses the same coupe shape and the same panel dimensions. A shop that has wrapped one F1 can use the same film measurements for another. No newer body adds length or extra panels to the estimate.

Questions about wrapping a McLaren F1

How much vinyl does it take to wrap a McLaren F1?

A McLaren F1 full wrap takes about 43 ft (13 m) of 60-inch (1.52 m) cast vinyl. If you choose chrome or patterned film, the amount rises to roughly 54 ft (16.5 m) because of pattern matching and material handling. These figures are for the coupe body of the only generation made.

Can I wrap only the hood or the roof of a McLaren F1?

Yes, you can wrap only the hood or the roof of a McLaren F1. A partial wrap can cover the roof, hood, and mirror caps in the color of your choice. A chrome delete for the window trim and badges is also an option. Clear paint protection film (PPF) on the front end protects the nose without a color change.

Is a McLaren F1 hard to wrap?

Yes, a McLaren F1 is hard to wrap because of its small size and two long side doors. Each door is one large piece of film that must follow the deep side intakes and wrap around the edges. The car's short 168.8 in (4,288 mm) length leaves little flat area for easy film positioning. Removing panels and mirror caps for a seamless finish also adds time.

How many generations of the McLaren F1 does this page cover?

This page covers one generation of the McLaren F1, produced from 1992 to 2000. There is only one body style in the catalog: a two-door coupe. Every wrap estimate on this page applies to that single generation.