Wraps by car

McLaren P1 wrap

This page covers the McLaren P1, a sports car produced from 2012 to 2017 in one generation. A full vinyl wrap of the coupe body uses about 51 ft (15.5 m) of 60-inch (1.52 m) cast film. Chrome or patterned film raises the estimate to about 57 ft (17.5 m).

1generations15.5 mof film for a full wrap

McLaren P1, first generation, factory photo
McLaren P1, first generation. Factory color shown.

McLaren P1 wrap colors and ideas

  • McLaren P1 black wrap
  • McLaren P1 white wrap
  • McLaren P1 gray wrap
  • McLaren P1 silver wrap
  • McLaren P1 red wrap
  • McLaren P1 blue wrap
  • McLaren P1 green wrap
  • McLaren P1 yellow wrap
  • McLaren P1 orange wrap
  • McLaren P1 purple wrap
  • McLaren P1 pink wrap
  • McLaren P1 teal wrap
  • McLaren P1 brown wrap
  • McLaren P1 gold wrap
  • McLaren P1 chrome wrap
  • McLaren P1 color shift wrap
  • McLaren P1 carbon fiber wrap
  • McLaren P1 camo and patterned wrap

How much vinyl to wrap a McLaren P1

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2012–2017coupe (2 doors)180.6 in (4,588 mm)about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m)

McLaren P1 wrap cost factors

The McLaren P1 wrap cost depends on film choice, surface condition and the number of cut-outs. Standard cast film for this 180.6 in (4,588 mm) coupe takes about 51 ft (15.5 m), while chrome or patterned film takes about 57 ft (17.5 m). A full wrap adds labor for the long doors and low front splitter.

  • Film for a full wrap: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

McLaren P1 wraps by generation

Swipe sideways. Tap a card for the full description.

McLaren P1, first generation, factory photo
Factory color shown

2012–2017 McLaren P1 coupe (first generation)

2012–2017coupe (2 doors)180.6 in (4,588 mm)

The first-generation McLaren P1 was built from 2012 to 2017 as a coupe. Paint age matters on a car of these years because panels may be original or repainted. A test spot comes before a full wrap to check film adhesion.

Two long side doors: each door is one large piece of film.

Film: about 51 ft (15.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 57 ft (17.5 m).

Roof, hood, chrome delete and PPF on a McLaren P1

A partial wrap on a McLaren P1 can cover the roof, hood or mirror caps. Chrome delete covers window trim and badges with black film. Paint protection film (PPF) is a clear film applied to the front end.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a McLaren P1: body, cut-outs and film

The McLaren P1 is a two-door coupe with a length of 180.6 in (4,588 mm). Its long, low body means a McLaren P1 vinyl wrap needs large, continuous panels. The side of the car from door to rear fender is one of the biggest single pieces on the car.

The two long side doors are each wrapped as one large piece of film. For clean edges, you remove door handles, mirrors and trim before applying film. Emblems and badges come off for a seamless finish.

If you need to know how much vinyl to wrap a McLaren P1, use 51 ft (15.5 m) for the first-generation coupe made from 2012 to 2017. This single generation has no earlier or later body to compare. The estimate covers the full exterior with no waste factor included.

Questions about wrapping a McLaren P1

How much vinyl does it take to wrap a McLaren P1?

Yes, it takes about 51 ft (15.5 m) of 60-inch (1.52 m) cast film to wrap a McLaren P1. For chrome or patterned film, the estimate is about 57 ft (17.5 m). This covers the full coupe body of the 2012–2017 generation.

Can I wrap only the hood or the roof of a McLaren P1?

Yes, you can wrap only the hood or the roof of a McLaren P1. Other partial jobs include mirror caps, a chrome delete or paint protection film on the front end. These smaller wraps use far less film than a full wrap.

Is a McLaren P1 hard to wrap?

Yes, a McLaren P1 is hard to wrap because each long side door must be one large piece of film. The 180.6 in (4,588 mm) length and deep curves add work. Installers remove parts like handles and badges for a clean result.

How many generations of the McLaren P1 does this page cover?

This page covers one generation of the McLaren P1, built from 2012 to 2017. It is a coupe with two long doors. No other generation is in the catalog.