Wraps by car

TVR Cerbera wrap

The TVR Cerbera wrap page covers the first generation sports car built from 1994 to 2003. This generation is the only one in the catalog. A full vinyl wrap of the coupe body takes about 46 ft (14 m) of 60-inch (1.52 m) cast film.

1generations14 mof film for a full wrap

TVR Cerbera, first generation, factory photo
TVR Cerbera, first generation. Factory color shown.

TVR Cerbera wrap colors and ideas

  • Cerbera black wrap
  • Cerbera white wrap
  • Cerbera gray wrap
  • Cerbera silver wrap
  • Cerbera red wrap
  • Cerbera blue wrap
  • Cerbera green wrap
  • Cerbera yellow wrap
  • Cerbera orange wrap
  • Cerbera purple wrap
  • Cerbera pink wrap
  • Cerbera teal wrap
  • Cerbera brown wrap
  • Cerbera gold wrap
  • Cerbera chrome wrap
  • Cerbera color shift wrap
  • Cerbera carbon fiber wrap
  • Cerbera camo and patterned wrap

How much vinyl to wrap a TVR Cerbera

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1994–2003coupe (2 doors)168.5 in (4,280 mm)about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m)

Cerbera wrap cost factors

Cerbera wrap cost depends on the condition of a 1994 to 2003 TVR Cerbera before the film goes on. Paint age on this car means panels may be original or repainted, so a test spot comes before a full wrap. The amount of film is fixed at about 46 ft (14 m) for solid cast, but extra prep work adds labor time.

  • Film for a full wrap: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m).
  • Body: coupe (2 doors).
  • Two long side doors: each door is one large piece of film.

Cerbera wraps by generation

Swipe sideways. Tap a card for the full description.

TVR Cerbera, first generation, factory photo
Factory color shown

1994–2003 Cerbera coupe (first generation)

1994–2003coupe (2 doors)168.5 in (4,280 mm)

The first generation TVR Cerbera from 1994 to 2003 may have original or repainted panels. In a car of these years, paint condition varies, and a test spot comes before a full wrap. The single coupe body and 168.5 in (4,280 mm) length make film coverage predictable once the surface is sound.

Two long side doors: each door is one large piece of film.

Film: about 46 ft (14 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 52 ft (16 m).

Roof, hood, chrome delete and PPF on a Cerbera

The Cerbera chrome delete covers window trim and badges with black film for a cleaner look. A partial wrap on this car typically includes the roof, hood, and mirror caps. Paint protection film (PPF) is clear film on the front end to guard against stone chips.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a TVR Cerbera: body, cut-outs and film

The TVR Cerbera vinyl wrap has one body style, a two-door coupe, which simplifies film planning. Its length of 168.5 in (4,280 mm) means a standard roll width of 60 inches (1.52 m) covers most panels without seams. The two long side doors each take one large piece of film, so a careful installer can avoid visible joins on the flanks.

Cerbera wrap ideas start with the two long side doors, which need one large piece of film per door. The door handles, mirrors, and side repeaters are removed or cut out for a clean finish. The front and rear bumpers require relief cuts and heat forming around the curves.

How much vinyl to wrap a Cerbera stays the same because there is only one generation, from 1994 to 2003. A first-generation coupe uses about 46 ft (14 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds about 6 ft (2 m), for a total of 52 ft (16 m).

Questions about wrapping a TVR Cerbera

How much vinyl does it take to wrap a TVR Cerbera?

Yes, it takes about 46 ft (14 m) of 60-inch (1.52 m) cast film to wrap a TVR Cerbera. For chrome or patterned film, the estimate is 52 ft (16 m).

Can I wrap only the hood or the roof of a Cerbera?

Yes, you can wrap only the hood or the roof of a TVR Cerbera. A partial wrap often includes the roof, hood, and mirror caps, but a single panel is also a common smaller job.

Is a Cerbera hard to wrap?

The TVR Cerbera adds work because it has two long side doors, each one large piece of film. The car is 168.5 in (4,280 mm) long, so the doors require careful handling and a second pair of hands. The coupe shape is defined, and the door length is the main challenge.

How many generations of the Cerbera does this page cover?

This page covers one generation of the TVR Cerbera, from 1994 to 2003.