Wraps by car

Xpeng P7i wrap

The Xpeng P7i wrap page covers the first-generation sedan from 2023 to now, which needs about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a full vinyl wrap. This page gives the measurements, panel notes and planning points for a complete color change. Use it to estimate film, compare partial jobs and decide if a gloss, matte or satin finish suits the body. One generation and one four-door body keep the numbers simple to work with.

1generations18.5 mof film for a full wrap

Xpeng P7i wrap colors and ideas

  • Xpeng P7i black wrap
  • Xpeng P7i white wrap
  • Xpeng P7i gray wrap
  • Xpeng P7i silver wrap
  • Xpeng P7i red wrap
  • Xpeng P7i blue wrap
  • Xpeng P7i green wrap
  • Xpeng P7i yellow wrap
  • Xpeng P7i orange wrap
  • Xpeng P7i purple wrap
  • Xpeng P7i pink wrap
  • Xpeng P7i teal wrap
  • Xpeng P7i brown wrap
  • Xpeng P7i gold wrap
  • Xpeng P7i chrome wrap
  • Xpeng P7i color shift wrap
  • Xpeng P7i carbon fiber wrap
  • Xpeng P7i camo and patterned wrap

How much vinyl to wrap a Xpeng P7i

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2023–nowsedan (4 doors)192.1 in (4,880 mm)about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m)

Xpeng P7i wrap cost factors

Xpeng P7i wrap cost depends on the film you pick, the wrap shop's labor rate and the size of the sedan, which is 192.1 in (4,880 mm) long and takes about 61 ft (18.5 m) of film. A color change wrap costs more than a partial job because the whole body is covered, and chrome film or patterned film adds waste from matching. If you add several wrap ideas like the charge port door or the door handles, those small pieces raise the labor time. The final figure also changes with the prep work the car needs, such as paint correction before the vinyl goes on.

  • Film for a full wrap: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).
  • Body: sedan (4 doors).
  • Electric car: the charge port door is wrapped as a small piece of its own.

Xpeng P7i wraps by generation

Swipe sideways. Tap a card for the full description.

2023–now Xpeng P7i sedan (first generation)

2023–nowsedan (4 doors)192.1 in (4,880 mm)

The first generation Xpeng P7i is a four-door sedan that is 192.1 in (4,880 mm) long and takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film. The length is split across the long roof, the four doors and the front fenders, so you need a full roll of film and more than fifteen panels. The rear doors are shorter than the front doors, but each one still needs its own piece of vinyl. The sedan shape means no vertical tailgate or tall hatch, which keeps the rear wrap simpler than on an SUV.

Electric car: the charge port door is wrapped as a small piece of its own.

Film: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 69 ft (21 m).

Roof, hood, chrome delete and PPF on a Xpeng P7i

A partial Xpeng P7i wrap can be just the roof, the hood or the mirror caps, and a chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is a clear wrap that can be put on the front end only, including the bumper and part of the hood. These jobs use much less film than a full wrap and still change the look or protect the paint. The roof on this long sedan is a good single panel to start with.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping a Xpeng P7i: body, cut-outs and film

An Xpeng P7i vinyl wrap covers a four-door sedan body that is 192.1 in (4,880 mm) long, so the roof and the lower sills are long, flat runs. The four doors and the front and rear fenders are separate panels, and each one has to be wrapped individually. The rear bumper is deep and curved around the rear lights, so it takes more stretching than a flat panel. The hood is wide but not unusually long, and the trunk lid is a single piece that wraps over the rear edge.

Xpeng P7i wrap ideas start with the charge port door, which is wrapped as a small piece of its own so it can open cleanly later. The flush door handles add time because each handle has to be tucked or removed and wrapped separately. The front bumper has several large openings and the lower lip is a sharp edge. The shark-fin antenna and the side mirror caps are also small pieces that need careful cutting.

To know how much vinyl to wrap a Xpeng P7i, you count the only body in the catalog: the first generation from 2023 to now. A full wrap of it takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film, and chrome or patterned film takes about 69 ft (21 m) for pattern matching. The four doors and the long roof mean you will use almost all of a 5 ft wide roll on most panels. Since there is one body style, the film estimate does not change between trims.

Questions about wrapping a Xpeng P7i

How much vinyl does it take to wrap a Xpeng P7i?

A Xpeng P7i takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a full wrap, and about 69 ft (21 m) if you use chrome or patterned film. The lower cast film figure fits a single color wrap with careful nesting on the long sedan body. The higher figure accounts for matching patterns across the four doors and the roof. No extra film is needed for the charge port door because it is cut from the same rear quarter piece.

Can I wrap only the hood or the roof of a Xpeng P7i?

Yes, you can wrap only the hood or the roof of a Xpeng P7i, and both are standard partial jobs. The roof is one long, flat panel that is easy to wrap in one piece, and the hood is wide but has simple edges. A Partial wrap can also be the mirror caps alone, and a chrome delete covers the window trim and badges with black film. Paint protection film (PPF) is another partial option that puts clear film on the front end only.

Is a Xpeng P7i hard to wrap?

A Xpeng P7i is not harder to wrap than other long sedans, but its electric charge port door adds one extra step. That door is wrapped as a small piece of its own so it can still open, which means an extra cut and a separate piece of film. The 192.1 in (4,880 mm) length means the roof and the lower sills are very long, so you need a second person to lay the film flat. The flush door handles also add time because they have to be tucked or removed.

How many generations of the Xpeng P7i does this page cover?

This page covers one generation of the Xpeng P7i, the first generation produced from 2023 to now. There are no older or newer body styles listed, so the measurements, film estimate and wrap notes all apply to that sedan. If you see a different Xpeng P7i body, it is not covered here. The single-generation catalog makes it easy to order the right amount of vinyl.