Wraps by car

Acura RLX wrap

The Acura RLX wrap page covers the full-size sedan built from 2013 to now, with one generation in the catalog. A vinyl wrap on this car uses about 61 ft (18.5 m) of 60-inch (1.52 m) cast film for a standard color change. Chrome or patterned film requires more material, around 70 ft (21.5 m).

1generations18.5 mof film for a full wrap

Acura RLX, first generation, factory photo
Acura RLX, first generation. Factory color shown.

Acura RLX wrap colors and ideas

  • Acura RLX black wrap
  • Acura RLX white wrap
  • Acura RLX gray wrap
  • Acura RLX silver wrap
  • Acura RLX red wrap
  • Acura RLX blue wrap
  • Acura RLX green wrap
  • Acura RLX yellow wrap
  • Acura RLX orange wrap
  • Acura RLX purple wrap
  • Acura RLX pink wrap
  • Acura RLX teal wrap
  • Acura RLX brown wrap
  • Acura RLX gold wrap
  • Acura RLX chrome wrap
  • Acura RLX color shift wrap
  • Acura RLX carbon fiber wrap
  • Acura RLX camo and patterned wrap

How much vinyl to wrap an Acura RLX

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
2013–nowsedan (4 doors)196.1 in (4,982 mm)about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m)

Acura RLX wrap cost factors

An Acura RLX wrap cost depends on the size of the sedan, the film type and how many parts are removed for a clean install. The car takes about 61 ft (18.5 m) of cast film for a color change, and chrome or patterned film pushes the material need to about 70 ft (21.5 m). The four doors and the long roof add labour compared with a smaller sedan, and the front bumper sensors need careful cut-outs. A partial wrap or chrome delete uses less film and less time than a full color change.

  • Film for a full wrap: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).
  • Body: sedan (4 doors).
  • Restyled in 2017: bumpers and lights differ between the versions, and so do the film cuts.

Acura RLX wraps by generation

Swipe sideways. Tap a card for the full description.

Acura RLX, first generation, factory photo
Factory color shown

2013–now Acura RLX sedan (first generation)

2013–nowsedan (4 doors)196.1 in (4,982 mm)

The first generation Acura RLX ran from 2013 to now, and the 2017 restyling changed the bumpers and lights. A film kit cut for the 2013–2016 front bumper will not fit a 2017 or later car, and the same goes for the rear bumper pieces. The sides of the body stayed the same, so door, fender and quarter panel templates can be shared across all years. Installers keep separate patterns for the two bumper versions to avoid re-cutting on the car.

Film: about 61 ft (18.5 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 70 ft (21.5 m).

Roof, hood, chrome delete and PPF on an Acura RLX

For a partial wrap on the Acura RLX, the roof, hood and mirror caps are the most straightforward panels to cover in one colour. A chrome delete on this car means covering the bright window trim and the badges with black film, which takes less than a day to cut and apply. Paint protection film (PPF) is a clear film applied to the front bumper, part of the hood and the mirror caps to guard against stone chips. Any of these jobs can be done without wrapping the full sedan.

  • Partial wrap: roof, hood, mirror caps.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film on the front end, also over a wrap.

Wrapping an Acura RLX: body, cut-outs and film

An Acura RLX vinyl wrap has to cover a body that measures 196.1 in (4,982 mm) long with four doors. The sedan shape keeps the main panels flat and wide, so the installer can lay film on the hood, roof and trunk without excessive stretching. The rear doors are long for a sedan, which means each side needs a single large piece rather than small offcuts. The rear bumper wraps around the tail lights and needs relief cuts to sit cleanly in the corners.

For Acura RLX wrap ideas, the door handles and mirror caps come off to let the film tuck behind them instead of cutting on the paint. The front bumper has parking sensors and a radar cover that need precise cut-outs, and the grille surround is best wrapped with the bumper off the car. The tail lights and headlights stay in place but the film is trimmed tight to the lenses with a knifeless tape line. The antenna fin on the roof is wrapped in two pieces because it does not detach without dropping the headliner.

When counting how much vinyl to wrap an Acura RLX, the sedan body has stayed the same shape for the whole run, so the panel sizes are consistent. The 2017 restyling changed only the front and rear bumpers and the light shapes, not the doors, roof or quarter panels. A kit cut for a 2013 to 2016 car will fit the hood and sides of a later car, but the bumper pieces will not match. Order film by the full-sheet estimate and keep offcuts for the small trim parts.

Questions about wrapping an Acura RLX

How much vinyl does it take to wrap an Acura RLX?

It takes about 61 ft (18.5 m) of 60-inch (1.52 m) cast film to wrap an Acura RLX in a standard colour. If the film is chrome or has a pattern that must be matched, the figure rises to about 70 ft (21.5 m). The estimate covers the whole sedan body with enough offcuts for the mirrors and door handles.

Which years of the Acura RLX take the same film cuts?

The 2013–2016 Acura RLX models share one set of film cuts, and the 2017–now models share another. The 2017 restyling changed the front and rear bumpers and the lights, so the bumper templates are different before and after that year. The doors, roof and side panels are the same across all years.

Can I wrap only the hood or the roof of an Acura RLX?

Yes, the hood or the roof of an Acura RLX can be wrapped on its own. A partial wrap on this car commonly covers the roof, hood and mirror caps, but a single panel is also possible. The hood is flat and needs one piece of film, while the roof includes a small antenna fin that is wrapped separately.

Is an Acura RLX hard to wrap?

The Acura RLX is not hard to wrap, but its length of 196.1 in (4,982 mm) means the roof and side panels need large sheets of film. The front bumper has parking sensors and a radar cover that require careful cut-outs, and the grille surround is easier to wrap with the bumper off the car. The restyling in 2017 means two bumper versions exist, so the installer must have the right pattern for the year.