Wraps by car

Fiat Barchetta wrap

A Fiat Barchetta wrap covers the two-door convertible body of this Italian sports car, sold from 1995 to 2005. The car has one generation, though a facelift in 2003 changed the front end and rear lights. A full vinyl wrap of the newest body takes about 36 ft (11 m) of 60-inch (1.52 m) cast film.

1generations11 mof film for a full wrap

Fiat Barchetta, first generation, factory photo
Fiat Barchetta, first generation. Factory color shown.

Fiat Barchetta wrap colors and ideas

  • Barchetta black wrap
  • Barchetta white wrap
  • Barchetta gray wrap
  • Barchetta silver wrap
  • Barchetta red wrap
  • Barchetta blue wrap
  • Barchetta green wrap
  • Barchetta yellow wrap
  • Barchetta orange wrap
  • Barchetta purple wrap
  • Barchetta pink wrap
  • Barchetta teal wrap
  • Barchetta brown wrap
  • Barchetta gold wrap
  • Barchetta chrome wrap
  • Barchetta color shift wrap
  • Barchetta carbon fiber wrap
  • Barchetta camo and patterned wrap

How much vinyl to wrap a Fiat Barchetta

Estimates from the body dimensions in the catalog, for a 1.52 m (60 in) roll.

YearsBodyLengthFilm to order
1995–2005convertible (2 doors)154.2 in (3,916 mm)about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m)

Barchetta wrap cost factors

A Barchetta wrap cost depends on the film chosen, the number of cut-outs in the panels, and whether the bumpers and mirrors are removed. The car is 154.2 in (3,916 mm) long, so a full wrap uses about 36 ft (11 m) of 60-inch (1.52 m) cast film. Chrome or patterned film adds roughly 12 ft (3.5 m) to the order because of pattern matching.

  • Film for a full wrap: about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).
  • Body: convertible (2 doors).
  • Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.
  • Restyled in 2003: bumpers and lights differ between the versions, and so do the film cuts.

Barchetta wraps by generation

Swipe sideways. Tap a card for the full description.

Fiat Barchetta, first generation, factory photo
Factory color shown

1995–2005 Barchetta convertible (first generation)

1995–2005convertible (2 doors)154.2 in (3,916 mm)

The Barchetta's open top means the wrap ends where the fabric roof begins, so there is no roof panel to cover. The film is wrapped over the top edges of the doors and rear quarter panels and tucked behind the rubber seals. A chrome delete on the window trim can run from the base of the windshield to the rear deck, giving a clean line around the open cabin.

Convertible body: a fabric top is not wrapped and the film ends where it begins; a folding hard top is wrapped as panels of its own.

Film: about 36 ft (11 m) of 60-inch (1.52 m) cast film; chrome or patterned film: about 48 ft (14.5 m).

Roof, hood, chrome delete and PPF on a Barchetta

You can order a partial wrap for the Barchetta, such as the hood, mirror caps, or rear deck, which uses far less film than a full wrap. A Barchetta chrome delete covers the window trim and badges with black film, usually taking less than half a day. Paint protection film (PPF) in clear is often applied only to the front end, including the hood and bumper.

  • Partial wrap: hood, mirror caps, rear deck.
  • Chrome delete: window trim and badges.
  • Paint protection film: clear film for the front end, which can also go over a wrap.

Wrapping a Fiat Barchetta: body, cut-outs and film

A Fiat Barchetta vinyl wrap is small enough to be handled by one installer, but the long doors and curved rear haunches take care to lay the film smoothly. The car is 154.2 in (3,916 mm) long and has no roof to wrap, which lowers film use compared with a closed car. The fabric top is left uncovered and the film ends cleanly where the top begins.

For Barchetta wrap ideas, the most demanding part is the front bumper, where the film must be cut around the small grille and fog lights. The door handles and mirrors come off for a clean edge, and the badges are removed before the panel is wrapped. The fuel filler flap is usually wrapped separately so the hinge and lock stay free.

To work out how much vinyl to wrap a Barchetta, start with the base figure of about 36 ft (11 m) of 60-inch (1.52 m) cast film. The 2003 restyle changed the bumper shapes and added a new rear light cut-out, but the overall film use stays about the same. Pre-facelift cars have a smaller front grille, slightly reducing the film needed for the bumper.

Questions about wrapping a Fiat Barchetta

How much vinyl does it take to wrap a Fiat Barchetta?

A Fiat Barchetta needs about 36 ft (11 m) of 60-inch (1.52 m) cast film for a full wrap. This figure is for the newest body style, the convertible sold from 1995 to 2005 with the 2003 facelift. If you use chrome or patterned film, plan for about 48 ft (14.5 m) because of waste from matching the pattern.

Is the top of a Barchetta wrapped?

No, the top of a Barchetta is not wrapped. The fabric top is left uncovered, and the wrap ends where the roof begins with a clean edge tucked behind the seal. If the car has a folding hard top, those panels can be wrapped separately, but the soft top itself is never covered with vinyl.

Which years of the Barchetta take the same film cuts?

All Barchetta models from 1995 to 2005 take the same basic film cuts for the doors and rear panels. The main changes concern the front and rear bumpers, because the restyle of 2003 introduced new shapes for those parts. For a full wrap, you should order cuts for the correct bumper type, pre- or post-facelift.

Can I wrap only the hood or the roof of a Barchetta?

Yes, you can wrap only the hood or the rear deck of a Barchetta; the roof is fabric and cannot be wrapped. A partial wrap can cover the hood, mirror caps, or rear deck, and a chrome delete covers the window trim and badges. Paint protection film is often applied to the front end, including the hood and bumper, without wrapping the whole car.